happy with plants at this stage. cant wait to see them bulk up. they are starting to smell a little now the sour lemon tart is alot more pungent than critical orange punch at this stage.

The girl looks really good, strong thick branches, which I wanted to bend a little more, but I don't have the space for that :D :D The girl hasn't started to show her flowers yet, but I think that in a few days, it should appear :) good luck to everyone.

June 7 - We ordered some new lights last week, they are 240w kingbrite samsung lm310h with uv/ir, 3000k, and meanwell drivers. We setup the new room and moved the girls into there. After a bit of LST and a watering (with nutrients) at roughly 7ph, they were ready to go under the 2 new lights and the same SF-1000 we have been using in this grow. The new room is a 12 ft enclosed trailer. I moved everything from the small tent into this. I put clear poly on the walls, floor and ceiling. I put poly on the shelf I am going to be keeping in there as well. I bought 50ft of 6mm mylar and lined the floors, roof and sides with it. I plan to get some reflective tape to seal everything and to cover the wood. I did not get much of a chance to watch temp's today as they it was later in the evening after all was said and done. The inline fan blowing in air from outside. June 8 - 9 AM i checked the plants, they were at 25.2 and 50% RH. Late through the day I had checked and we had gotten up to around 32 degrees. So I moved the inline fan to the closer vent, hooked up to that, and had the air blowing out of the trailer with the inline fan sucking it from above the lights. I then added oscillating fan and had it blowing air on the left side of the room so it would somewhat circulate once I closed the doors. I then checked at about 9pm and we were at 22 degrees. Definitely noticed a decent amount of growth already. I have the lights on a 22/2 cycle as I was worried about the heat at night time. June 9 - Some great growth from the girls, still having problems controlling the temps in the afternoon. I decided to prop the door open a bit to have a constant breeze throughout the day while I am at work. Decided to do some more LST and also a bit of defoliation. I took about 25% of the leaf's that were blocking the new growth as it was getting a bit bunched up. I was then told the leaf's are almost solar panels for them. So from now on I will be trying to just do some tucking unless needed. The leaf's I removed were most of the damaged leaf's, I am not to sure if that makes much of a difference. I gave them a watering with only water as there is a potential I am getting a bit of a nutrient buildup along with the PH problem. Or potentially the reason for the ph problem is nutrient buildup. After watering with A PH of 7 I got some run off and tested it. The smaller plant gave me a PH of about 5.5 where the bigger one is around 5.0. June 10 - Plants are looking happy and showing tons of growth. Seems to be trying to stretch outwards. Not a ton of sign of PH issues showing so potentially getting it under control. Still a bit of damage to previous leaf's but it is what it is! The last few days I have been leaving the door open a bit in order to keep the temps down. I decided to test something and turn the lights off (automatically) at 11AM and back on at 5PM so light schedule has now changed to 18/6 and it seems I may have figured out the issue. We haven't had lots of sun the last couple days so it hasn't been to hard and I have yet to know if it truly fixed the heat issue for now. (I will be looking into a ac unit as well since it typically gets to around 30-35 around here. June 11 - Pulled some of the branches back down and added a few more LST spots. Seems we have a good amount of growth from the smaller plant out of the 2 topped spots. Unfortunately it looks like I fucked up on the bigger plant and only one of the nodes seems to have new growth. I will continue to monitor that but I think I cut the node to low and also to soon. Other then that, the girls are doing great. They seem to be absolutely loving these new lights. I gave them some nutrient water today as well. roughly 3L each. They seem to be A hell of A lot more thirsty under these new lights. June 12 - The girls are doing great , they are still just doing growing away. Lots of progress everyday. I am going to be getting a go-pro so I can set-up a time-lapse for the rest of this grow. I received my new inline fan, I got A ac infinity CLOUDLINE T4 with the temperature humidity controller. I am going to be having one fan pushing fresh air in and one fan pulling out the hot air. I will be doing that tomorrow since I have to work today. June 13 - I ordered another 50ft of mylar and that showed up today. I have decided to remove the shelf and add another 3+ feet to the grow space. So today I installed more poly, mylar, the ac infinity fan. I have it set-up to pump in air if it gets to warm. I am thinking of switching it to the output that way if it gets to hot or to humid I can have that air pulled out of the trailer. Right now my other inline fan is the outtake and I just have it set on full. Overall I think everything is set-up a bit better and more accessible. I will be putting my 2x2 tent in there at the left of the doors so I can have a veg room when these 2 are in flower. I plan to have 4 in veg and 4 in flower for the next grow. Still waiting on JOTI seeds, ordered 3 weeks ago and still have not been shipped. I will be getting those going the moment they arrive. The girls seem to be happy still, did a bit more LST to try to keep everything even, mainly I'm just pulling down on the spots I already have tie wire on.

Looking frosty and stacking up

Hiiigh friends 🙌 Welcome to week 8. 😍 Due to too much unwanted stress, flowering is delayed. The big lady was unable to withstand the training. Her neck is broken. But she is far from giving up and will fight to the end.. 😊 See you next week. 👋 Arturo for KannaKullektiv 🙏

First sign of preflowers, it's been 7 days since the flip. I'm just winging it like I do with everyday life 🤣😆 They both seem happy enough, if anything the watermelon looks like a could pull back on the nitrogen a little but we'll see. (Update... 14 days since flip) The cheese was a male, absolutely gutted. I thought I was seeing things when I saw male sac, none where open so got it in time but how can it just be a straight up male when they're supposed to be feminised seeds? Crazy bad luck or what? If anyone wants to chuck their two cents in I'll happily take the knowledge. The seed was Cheese from Barneys, I've never had this problem with them before but it knocks my confidence with them a bit. On the other hand the Watermelon Zkittlez is coming along nicely, next week's update will be updated on Monday. Peace ✌️

fat dense buds numerous and fuzzed out with trichomes. leaf-calyx ratio on point. Stalks tended to lean as flowering progressed so plan for some manner of support if you want. Let her flower as long as she can and she’ll reward you.

26.10 Took clones from all of the plants they i didn’t have backups for. Took out all the small branches and lolipopped a bit. They look fantastic and it’s one of my best starts of flower yet.

Algunos de ellos conforme pasan los días de floracion el tallos se está poniendo rojo. Y también sin desmerecer las luces de mars hydro son la bomba la. Mejor luz que puede comprar marshydro Espero tener una buena cosecha.

These are getting ready to go into flower around end of july early au

7/14: Watered her today. Just plain water. Filled up half gallon jug of water. Filled reservoir back first line. 7/16: Bumped light intensity to 45%. Topped off reservoir at night. 7/18: Watered her today with the the leftovers of some treated water with Rapid Start from her half gallon jug. Prepping for new nutrient schedule next week. I am happy to say it seems like the WCC is responding well to the environment and feeding schedule. So Far So Good!!! 😁 Thinking of possibly starting LST next week. Please Comment if anybody sees anything wrong in the pics!?!?!? 👍 Also any tips on how-to/when to start LST would be greatly appreciated! ***** For this Grow****** “Day Air Temperature” will be the max temp of tent for the week. “Substrate Temperature” will be the average temp of tent for the week. “Night Air Temperature” will be the lowest temp of the tent for the week.

1/12/26 4:18AM MONDAY.....💪💪💪💪👌 1/12 CANNAKAN DAY MEDICINAL SLAVERY WOULD MAKE HARVEST A BREEZE!! ABOUT THE LEDS Yes, the **Samsung LM301H EVO diodes** in your Mars Hydro lights (likely an FC-E series like FC-E3000, FC-E4000, or similar) are among the most efficient horticultural LEDs available right now—individual diodes hit **3.14 μmol/J** efficacy, pushing the whole fixture to around **2.85–2.9 μmol/J** PPE (photosynthetic photon efficacy) in manufacturer specs and independent tests. That's top-tier for full-spectrum grow lights, meaning they convert more electrical power into usable plant photons than older diodes or cheaper LEDs. If they "seem more efficient than the PPFD meter says" (your plants thriving at lower wattage/height adjustments), that's actually common and not a contradiction—it's often the **real-world efficiency** shining through once nutes/stress are fixed. Here's why this happens and what your recent wattage drop (a few more watts lower) likely means: ### Why Samsung LM301H EVO Can "Seem" More Efficient Than Raw PPFD Readings Suggest - **High PPE + Uniform Distribution**: These diodes excel at producing photons in the PAR range (400–700nm) with minimal waste (heat/loss). Mars Hydro FC-EVOs achieve strong average PPFD (e.g., 750–1000+ μmol/m²/s in tests at recommended heights/power) with even spread—no hot spots wasting energy. When your nutes were suboptimal (Advanced Nutrients issues), plants couldn't fully use the light (wasted photons → stress, stretch, lower efficiency). Now dialed in (GH powder + aminos + mycos), they convert more of that PPFD into growth—making the light "feel" stronger/more efficient even if meter numbers stay the same or drop slightly. - **Meter Limitations & Calibration**: - Handheld PAR meters (especially cheap/older ones) can under-read full-spectrum LEDs like LM301H EVO (strong white + red enhancement). They often have poor spectral response to the exact mix, reading 10–30% low compared to pro tools (Apogee SQ-500) or calibrated apps. - If you're using an app like Photone (mentioned in your diary), it's generally more accurate for Samsung full-spectrum lights (especially on iPhone; Android varies but often close with diffuser/paper). Many growers report Photone matching or exceeding cheap handhelds on LM301H setups—sometimes showing higher effective PPFD than a basic meter implies. - Bottom line: Your plants are the ultimate meter. Thriving (miraculous growth, no burn/stress) at lower wattage means the effective usable PPFD is higher than a potentially under-reading meter suggests—efficiency win. ### Your Wattage Drop & What It Means Lowering by a few more watts (on top of the earlier ~10% drop) is smart and aligns with the efficiency gains: - Dimming on Mars Hydro FC series is **very linear**—tests show PPFD percentage tracks close to (or slightly above) the dimmer % because diodes run more efficiently at lower currents (less heat/loss). - Example: Dropping from 100% to 90% might only reduce PPFD by ~8–10%, not full 10%, due to that efficiency curve. - Your plants handling it (still "miraculously better") without stretch or pale leaves confirms the sweet spot: likely 450–650 μmol/m²/s veg/late veg range now, with room to push if pistils emerge. - Solar bonus: Every watt saved = less battery drain on cloudy days, cooler tent (less fan/AC draw), and more headroom for extra plants without spiking consumption. **Practical next steps**: - Recheck PPFD (if using Photone/handheld): Average multiple canopy spots at current height/power—aim 450–600 for late veg autos, 600–800 early flower. - Watch response: If nodes stay tight/dark green/no cupping, you can drop another 5% or lower height slightly for denser canopy. - Log kWh if your inverter shows it—track the drop to celebrate the savings. - If meter still "under-says" vs. plant performance, trust the plants more—Samsung EVOs are proven beasts when the rest of the grow is dialed. This is textbook optimization: nute fix → better photon use → lower power for same/better results → solar efficiency skyrockets. You're building a truly lean system. How low are you at now (e.g., 70–75W total?)? Any pistils or new growth explosions today? Keep the momentum—it's paying off big. 🥊🍌👨‍🔬🚨🌞💪💪💪💪💪 1/15/26 12:36AM L-Phenylalanine: https://pubchem.ncbi.nlm.nih.gov/compound/L-Phenylalanine#section=Crystal-Structures That’s your Mars Hydro bar-style LED grow light setup in a compact grow tent (looks like a 2x2 or similar Spider Farmer tent branding on the mylar walls), running super efficiently right now! Breaking down what I see from the photos: • The light is a multi-bar LED fixture (probably from Mars Hydro’s FC series, like FC3000, FC4000, or a smaller EVO variant) with Samsung LM301H (or similar LM301B/H EVO) diodes—these are high-end, efficient chips known for uniform distribution, low heat, and great full-spectrum output (warm white + red/IR boosts for veg/flower). • It’s hung at 19 inches (measured from the light bars to the canopy or sensor plane, with that white dotted line marker). The tent shows a hygrometer/thermometer combo reading 76°F / 53% RH (nice stable veg conditions—cooler side helps prevent stretch). • Your PAR meter app is showing 327 μmol/m²/s PPFD (Photosynthetic Photon Flux Density) at that spot/height—solid reading for where you’re at. • Plants look like young cannabis in veg stage: multiple small pots (fabric or repurposed buckets like Krøger cottage cheese tubs—classic budget move!), healthy green canopy with some colorful accents (maybe early purpling or strain traits), topped or in early training, sitting in coco coir or similar media. • Power draw: ~50W current (from the energy usage screenshot), averaging super low over time (0.48–0.76 kWh daily average). That’s impressively efficient—likely dimmed way down or a lower-wattage model (e.g., 150–300W rated, but running at partial power). Total consumption over 30 days at ~14.5 kWh is pennies on the electric bill. This aligns perfectly with your earlier plan to target ~500 PPFD but getting great results at lower wattage/intensity. Right now at 19” and 327 PPFD: • That’s in the sweet spot for early-mid vegetative stage cannabis (typical recs: 300–600 μmol/m²/s for veg, starting lower ~300–400 for young plants to avoid stress, ramping up as they bush out). • Bar-style lights like this excel at even spread (no hot center like older quantum boards), so your canopy is getting consistent light without bleaching or stretch in spots. • Low power (49.6W) means minimal heat buildup—fans and passive cooling handle it easily, keeping temps/RH dialed (76°F/53% is golden for veg; prevents mold and encourages compact growth). Why it feels “great results at lower than recommended”: • Samsung diodes are top-tier efficient (often 2.8–3.1 μmol/J), so you hit usable PPFD without cranking full power. • Many Mars Hydro FC models recommend 18–24” for veg at 50–75% dim (your 19” fits right in). • Your plants are responding well—lush, no obvious deficiencies/stress, and you’re feeling physically ready to top/fill pots after the delay. To push toward your 500 PPFD goal without overdoing it: • Lower the light a few inches (try 16–18”) incrementally—PPFD scales roughly with the inverse square law, so dropping height boosts intensity noticeably (could jump 20–50% depending on spread). • Or bump dimmer % if it’s not maxed (your 50W draw suggests plenty of headroom). • Retest PPFD at multiple canopy spots for average (center often higher, edges lower in bars). • Watch for tacoing/upward leaf curl (too much light) or stretch (too little). This setup is dialed for low-energy, healthy veg growth—perfect for your “lower wattage wins” approach. Plants are happy, tent’s stable, and you’re crushing it efficiency-wise. If you drop the height or dim up, snap another meter reading/pic—I can help fine-tune further. How old are these ladies (weeks from seed/clone)? Any specific strain notes, or planning to flip to flower soon? Keep the momentum—today’s a win! 🌱💪😂

Trocknung 8 Tage bei 60%rlf und ca 18 Grad 26% THC Gehalt 13.5% Restfeuchte und wasseraktivität von 0.4 jetzt beginnt das Curen.

Hi liebe Community and Welcome back! 💚 Der zweite Strain von Good Times Genetics. Entwickelt sich wunderprächtig und es sind sehr schöne große und Breitgefächerte Blätter zu erkennen. Ein schönes Wuchsbild verreint mit einer starken Indica Dominanz. Nach der ersten Blütenwoche entwickeln sich allmählich die Blütentriebe und die ersten Stigmen sind sichtbar. Also Düngerkomponenten kam das Greenhouse Feeding BioBloom und der entsprechende Enhancer zum Einsatz. Der Stängelabrieb duftet schon stark nach säuerlichen, dieselartigen Nuancen, mit einen etwas GMO typischen Aroma. Die Wachstumsbedingungen im Growzelt sind aufgrund der trockenen Heizungsluft zwar gut aber schon sehr trocken: ——————— 🌞 Temp: 22°C 🌚 Temp: 20 °C 💨 RH: 38% VPD: 1,33 kPa 😎PPFD: 830 mqm ——————— Stay Tuned! 💚

Dried straight on parchment-lined trays. Shawty's a super strong strain, 100% nighttime weed. Shawty total dry weight: 69g. Taste wise right now: mostly pine/forest with hints of skunk popping up here and there (not all buds). Aroma is gassy/diesel mixed with licorice, but it'll probably shift after curing. Occasionally get some berry vibes in places. Jury's still out too soon to call it. Shawty didn't smell strong at all during flower, so her aroma is much less pronounced/intense compared to Punchline. Surprisingly, Punchline has a way louder and more pungent smell. Spent roughly 4 to 4.5 hours on trimming this whole harvest. Not too bad, but my hands are done lol All the trimming leftovers are going straight to BHO Will update later once the flavors and aroma really pop and get more pronounced after curing

Week 5 had been amazing just that this week we had 3 days of rain which was great for the plant. I gave her some Tea again except that this time I use the rain water I collected. Which was ph at 6.3 and the run of off was ph at 6.8 The plant is around 10 inches now and I am starting to notice some red/purple lines on the stems. The smell is weak but it is still a little early to judge. I would really like some feedback you guys.

So jetzt habe ich die Uhr umgestellt auf 12/12

First of the 3 done. The other 2 are not ready and I'm hoping they can get though the next couple of weeks of cold

2021 - 08 - 29 Wedding Glue Auto 1 - most fan leaf are starting to turn yellow , Hoping she finished up in a week to 2. - Day 55 since sprout - trichomes are mostly milky, not much amber on buds yet. Wedding Glue Auto 2 - Some of the buds and fan leaf with abit of sugar leaf are turning purple... - Day 50 since sprout - She's fattening up nicely image format : Wedding Glue Auto 1-4.1 day 27 Wedding Glue Auto 1( plant strain and tag number) , 4 (week), 1 (image number) , day 27 ( Date since sprout )