Week 14 Update – Flower Week 3 🌸 The stretch is finally starting to slow down, and the canopy is settling into its final shape. The SCROG net has done its job, creating a much more even canopy with plenty of tops receiving direct light. Bud sites are stacking nicely across the tent, and white pistils are appearing everywhere as the plants shift their focus from vertical growth to flower production. The plants are drinking heavily and showing strong vigor despite the warm conditions. Airflow remains a priority as the canopy thickens, helping keep humidity under control and reducing the risk of mold later in flower. Overall, this week feels like the transition point where the garden stops stretching and starts building flowers. 📊 Current Stats 💧 Watering: 2L per plant every third day 🌡️ Temperature: 28°C 💦 Humidity: 65% RH 📈 VPD: ~1.39 kPa 💡 Light: ~800 PPFD 🕛 Light Schedule: 12/12 Looking ahead, the focus will be on maintaining a healthy canopy, good airflow, and consistent environmental conditions while the buds begin to bulk up over the coming weeks.

Lots of fan leaves ate growing back and I have lots of bud sites. Still feeding plagrons green sensation, sugar royal and power buds at half strength. I will remove all purple stems fan leaves around day 21 of flower.

🤗 Hi fellow growers. We are back here to harvest the Northern Lights Auto from Seedsman. She took 11 weeks to finish flower and a total of 15 weeks from seed to harvest. 🌱Growing her was a little tricky as she was finicky at the beginning of flower. She wasn't the fastest auto but she put on some tall colas with some fair amount of resin smelling of sour stone fruit such as a plum. Chopped her down then dryed for 14 days in a environment controlled room. Then began the trimming process. After a nice manicure the plum smelling buds were then placed in a jar to set cure for 30 days. There was quite a bit of larf nugs on the bottom skirts that I should have trimmed off during the flowering cycle but sometimes I like keeping them to press into some rosin before my nugs are cured. I find that pressing the flowers with in the first week of the curing process produces the best quality flower rosin In the end I'm left with a gram and a half of some beautiful Northern Lights flower rosin that tastes and smells like a sour plum and packs a big punch. About a 10% return so not the greatest yield but it sure is some high quality rosin. Keep it mind it was the larf flower and I press at 180°F to preserve as much flavor as I can. I'm after quality and have been achieving that. Effects - Relaxing, calming, Happy Yield - 68 g nice nuggets 14 g of larf that went to rosin Smell - Sour plum Forrest Taste - Skunky plums

Nice strain

🌿🌿🌿Happy plants 🌿🌿🌿 Watering every 2 day 0, 8 l Temp 20-30° Co2 1000 ppm Light 1100 ppfd RLF 30% GREAT WHITE 0,5G/L every week All plants seems to do well, no signs of heat stress or pests.. First signs of Flowers 🍀🍀 Bloom nutes + booster added 👌 😎👍

Started week 1 and we placed these girls in a 7 liter pot, they are now growing with 1x Marshydro TS1000 but im adding another TS1000 in 2 weeks when they start flowering

It took two ... 2 full hours to repot all 7 plants. I used an entire bag of Fox Farm Ocean Forest.... also sprinkled Mycorrhizal on each root system. The GG4 is really oing pretty good... I believe the tight node spacing means good things are in store. Super cropping continues. I gotta flip the whole lot of 7 plants...who cares .. first grow mistakes... fun!

Another great week, saw some great bud production and stacking. All great signs of a good yield. Increased the bloom nutrients to accommodate the plants demands during this intense growth spurt, while making sure they are balanced with a straight phd water feed to help break up any deposits that may be accumulating. When I use just water, I’ll water until I see about a 15% runoff, and test the ph of the runoff, should be within your 5.8-6.3 range. I’ve got lots of airflow keeping things moving to help prevent PM and pests. After every feed, I’ll spray a mixture of water, a drop or two of dish soap, and some type of essential oil, around the base of the pots and tent basin as part of my pest management/protection. I have yet to have any type of pests, despite growing in an unfinished basement situation. Happy Gardening 🇨🇦❤️👊

so far fully satisfied. the plant looks strong and a nice color. the first hairs are noticed. I notice signs of some parasites on the leaves, up to now I have only found about 2-3 small spiders clearly visible to the naked eye, and perhaps some other specimens of whiteflies. I accept advice on how to prevent an infestation in the best way.

12/09/25 - Another week for the Gorilla cookies but shes stacking on well still. The nugs are solid although pretty small theres soooo many. Watered 3L Ph 6.0 going to start tapering off the nutrients for this girl although ive not overfed her. Im thinking 1month left but with how fast it changed in 2weeks it could be in 2weeks 😆 13/09/25 - Watered 3L Ph 6.0 Looks like its got weeks left so keeping up with the bloom feed and biobizz 14/09/25 - Watered late last night so planning on watering early morning 15th Sep. Hospital trip messed up my watering scedule 😂 15/09/25 - Watered 3L Ph 6.0 16/09/25- Watered 3L Ph 5.9 17/09/25 - Watered 3: Ph 6.1 no bloom just Acti-vera

Arrrr the green crack has life in her yet , had some nice growth on this little runt she remains compact but has shown enough to keep around . Transplanted into her forever home in the 28L pot , even in her small state she was root bound in the 12 L , hope to triple her size this coming week .

🌿 C99 (Cinderella 99) – End of Week 2: Repotting Day & Into the Final Home! Weekly Update: The little C99 has been developing brilliantly over the past two weeks. However, the small starter cup (Red Solo Cup) reached its absolute limit—during repotting, a gorgeous, dense, and healthy white root system was revealed, having completely root-bound the cup. Time for the next big step! 🚀 Setup & Details: Container: Upgraded from the small cup to an 8.5-liter final pot Medium: Freshly mixed 50/50 Coco-Perlite mix (ideal for maximum aeration and drainage) Special Feature: An Airdome is installed at the bottom to supply the root zone with extra oxygen. Lighting (PPFD): Stable at 400 PPFD Feeding / Watering: Thoroughly watered in right after repotting with an EC of 1.4 and a pH of 5.8. Observations: The plant shows strong vigor, though it was starting to show slightly lighter leaves in the old cup as the nutrients were running low. The fresh coco/perlite mix combined with the tuned EC of 1.4 and pH 5.8 gives her the exact fuel boost she needs. The roots look pristine, and thanks to the Airdome and the increased volume, she is ready to explode in growth. Ready for Week 3! 🌿✨

Welcome to Week 6 or Flower Week 2 Media From Day 28 - 38 of: -Designers Club - Special Thanks to John for hopping through my Messages to Join The SSSC/DP Photo The Project will be Supported by Narcos Seeds to give the Strain the Perfect lifespan it could Deserve . Light used for The Contest Grow : Tenty Pro x4 200w in a space of 60x60 Homebox Ambiente Tent. Were only Starting with 2 Plants from Fast Version B . One didnt worked well . Both Topped Early at Day 9 as Project and Time Deadline from Contest . Everything Doing Well ive done some Mainlining and Defoliation over the days .One Growed a little bit special at the topping . Switched to Flower 12/12 today on Day 28 . Installed Scrog System at Day 29 Nutriets used/using now in Week 5 : -Narcos Root Stim -Narcos Bloom Stim -Narcos Hydro A+B Enough Talk from me , just Enjoy youre Seats and be a part of The Designers Club . Good Luck to Everybody and Keep up Growing !

11/24 Week begins and she is reaching that point. Feed tomorrow and some defoliation no flush yet as new hairs abound 11/27 Gave her some 6.5 water with a bit of recharge as her tricones are very dense, all white or amber (1%) and may be our most potent grow yet. Harvest in a few days after holiday.

23rd April and Current stage I am at Week 3 in to flowering and the buds are coming on very nicely with the THC shining nice on the buds and leaves (Hopefully I'm doing something right as it don't look to bad any advice would be appreciated)

The big day is here! 😎 Today, March 28th, 104 days (15 weeks) after germination, I have harvested my first indoor photoperiod plant. It has been an incredible challenge, especially managing it in the middle of a winter environment, but the results speak for themselves. 📏 Harvest Data (Wet Weight) -Total Wet Weight: 56.5 grams (15.7g + 40.8g). -Final Height: 40 cm of pure density. -Status: Rock-hard buds and an impressive resin layer. -Dry Estimate: I estimate that after water loss (60-70% less), the final dry weight will be between 14 and 17 grams, given how dense the buds are and the cold conditions we’ve faced. 🌡️ Process Summary -Managing a grow with lows of 12°C for my first indoor photoperiod experience has been difficult. I am aware that a climate control system would have been ideal, but the budget is what it is 😆. Despite the limitations, using lukewarm water for irrigation and controlling the lamp height were vital. This plant has been a great learning experience, and I am sure the next one will be much better, applying everything I’ve discovered during these 15 weeks. Now, on to a slow and controlled dry so the flavor is as spectacular as its look! I want to wrap up this diary by thanking everyone who has joined me during these 15 weeks. Your likes, and comments have been an extra motivation to pull this Critical through despite the cold challenges. It has been an incredible learning journey, and I couldn't be happier with the outcome of my first indoor photoperiod plant. See you all very soon with the Cream Caramel and that Main-Lining I have planned! Happy growing and happy smoking to everyone! 🌿💨

Hi guys, nothing seemed to happen this week, probably producing tricomes. I've upped the dosage of early flower and I'll start adding boost next week. Thanks for stopping by. Please check out my other diaries and feel free to leave a like, maybe even a follow and I'll be sure to check out your diaries to. The light being used Is the Mars hydro SP150, its a great quality light and is very bright, idea for a rectangular space. Visit www.marshydro.co.uk to purchase this and many other leds. Drgreen13#6724 (discord) Stay high, stay fly, #420everyday 🥃

For the Herbies contest - https://growdiaries.com/diaries/157348-grow-journal-by-dabbertglobberfield#gallery=6777378 - Grandmommy Purple is guilty multiple noise violations for being too loud and for stanky funk. Harvest - 169 days / 66 days in flower Well, we did it. I made it to the end. All I can think is...WOW that was A LOT of work. But I think I had very good results for a first time grower. I For harvest, we took Plant B and D and prepared them for immediate freezing. Altogether, I ended up with 1212g wet on plant B and 1089g wet on plant D. I ended up freezing 1816g of this. There was some from each of these plants that was set aside from freezing because, for whatever reason, I thought they were not worthy of washing because of how progressed the leaf damage was from the root rot battle. So that was cut up and dried as nuggets instead of hanging like the rest. Sawtooth and Plant C were both harvested and hung in the tent to dry for 12-13 days. I think I overdried by 1-2 days because when I jarred them they struggled to raise up to 55%. So I am using rh% packs. After drying Sawtooth and plant C, I ended up at 459.8g for dried flower and 170.8g in dried trim. So just over 1lbs between the 2 plants and 4.15lbs wet between the other 2 plants that was washed for hash. So... are you for real with the effort involved with washing bud for bubble hash? I don't think I would do this in the warmth. I only pursued doing bubble hash cause it's cold right now and I figured that would really help. Even in the 30s(fahrenheit) stuff would stick. It's hilarious how sticky of a process this is. I hope you have a bunch of gloves, water, and ice to burn through. I went through over 60 gallons of distilled water and 80lbs of ice to wash the 4 lbs. I am envious of people in videos using a hose to collect, clean, and refill. Also, doing this as a 1 person show is the definition of insanity. I broke the washings up into 3 parts. The first part was was the tester wash. I broke off 420g of plant D's 848gs available. I used 7 bags to see where I would end up. I used 220, 160, 120, 90, 73, 45, 25. What I determined was that if I was hunting a specific micron with a lot of material this would help find what you can get. But for the next washing I reduced the amount of bags to 4; 220, 160, 45, 25. The time, with the 4 bags, I washed with 809g. I had a much more favorable experience and return this second time but I had green fast and probably used too much ice. The 3rd wash was the remaining 631g and I found an extra 137g I added of sugar leaves and trim, brining the 3rd wash to 768g. I used 5 bags this time; 220, 160, 73, 45, 25. By the 3rd wash I have become an expert in collection but also never want to do it again. lol. 2 of the 3 washes have dried and I have 43.4g of bubble and 2.8g of dry sift. 37.4g of that bubble is able to be pressed into rosin. I will probably press that dry sift as well. The other stuff is 25u or 160u that I will experiment with or cook with. The other stuff is drying so I can't add it all in. I pressed a bunch of trim and some flower. The trim presses nice and the dab is decent. I am working out a good temp for the flower. But the problem with all these tests to find the sweet spot is that I have all these testers to go through but want to keep pressing and trying that! I think I will need to work on a better storage solution. I can't wait for the fresh frozen bubble hash rosin pressing... I have over 20gs of bubble to put in one bag. I am really looking forward to this. But I will need to work up to that pressing since I have never pressed hash/kief/bubble before in my rosin press. So this should be really fun. I will 100% post an update of the hash pressing once I do that and also after the 3rd wash session is done drying. In closing, saying I learned a lot from this grow would be an understatement. I fully expect to start it back up in a few weeks after some R&R then some R&D. There's some things I will need to work on before I start again, such as: having a single external reservoir that feeds multiple plants, hard to clog and easy to use ebb and flow system, miscellaneous final run stuff like space for drying. So thanks everyone for hanging out and perusing the photos and or reading all my huge rambling updates and thanks to those for the help along the way.