@0.8-0.9 kPa

FLOWER WEEK 5: Big Bang | Divine Seeds 💥 ​🌱 FLOWERING PROGRESS ​The Big Bang is hitting her absolute prime mid-bloom phase this week! 💥 The flower production has taken over completely, and the colas are swelling at a notable rate. The canopy is holding its uniform structure above the Scrog line, and the stacking is looking tight and intense. 📈 ​Trichome development has accelerated massively over the past few days, coating the main bud clusters and surrounding sugar leaves in a frosty layer of resin. The pistils are incredibly dense and long, forming thick, hairy white crowns on every single top. Overall plant vitality is outstanding as she continues to channel all her internal resources into maximizing bud volume and flower density. 🕸️✨ ​💧 NUTRIENT FEEDING & WATERING ​I’ve dialed up the organic nutrition line to match her peak-flowering hunger, pushing the main sugars, bio-stimulators, and energy enzymes to maximum levels. ⚡ ​Current Feeding Schedule (per Liter): ​Bio-Bloom: 3.0 ml/l ​Bio-Heaven: 4.0 ml/l ​Acti-Vera: 4.0 ml/l ​Bio-Grow: 1.0 ml/l ​Top-Max: 1.0 ml/l ​Calmag: 1.0 ml/l ​Parameters: ​pH: 6.5 ​Relative Humidity (RH): 59.0% 💧 ​Temperature: 30.0 °C 🌡️ ​VPD: ~1.73 kPa ​CO2: 675 ppm 💨 ​💭 GROWER'S NOTE ​👀 Status Report: Things are heating up in the tent! With temperatures hitting 30°C and a matching 59% RH, the VPD has pushed up to around 1.73 kPa. This high-performance climate means the Big Bang is transpiring at full speed. By upgrading the diet to 3 ml/l Bio-Bloom and boosting both Bio-Heaven and Acti-Vera to 4 ml/l, I'm giving her the massive energy reserves she needs to process nutrients at this high transpiration rate. Luckily, this solid Divine Seeds phenotype handles the summer-like conditions like an absolute tank. The buds are noticeably packing on frost and thickness daily. Keeping the airflow high and pushing hard through peak bloom! 🚀🌱✨

I'm extremely happy with how she's turning out, I want to give her another week, ideally 2.

officially flowering.. FINALLY

Hello everyone 🍀 The girls are in pre flowering stage! So far so good 🙏 Cheers 🍀 ❤️

Rather big and greedy plant, doesn't demand a lot of attention. Has shown good reaction to scrog and lst. I've already grown it once, and I'm sure I'll do it again. Довольно большое и прожорливое растение, не требует повышенного внимания, хорошо реагирует на scrog и lst. Поднимаю уже не в первый и точно не в последний раз:)

Week 4 no change to nutrient schedule, but plants are drinking faster as they grow so need to refill the reservoir a bit more. I had to photograph the plants on the evening before the day I would have usually take the pic's. When I came home a day later the plants grew A LOT!! They are about 8 inches now and very fluffy. I may have to clean up the branches on the bottom to avoid any issues.

TANGERINE DREAM™️ is an sativa dominant strain that offers tangy Tangerine aromas and flavours, giving an instant relaxing and cerebral high. Colas grow large and heavy, beautifully coated with red and orange trichomes.

.

Left these ones out a bit to long and not nearly enough love, so they suffered a bit but that's ok. I am going to experiment and try water curing the buds. First time ever using this method and I think it will make a good little project. No idea how to it will turn out, been reading it will remove most of the smells and that sucks but the smoke is very clean and light. Only time will tell. take about 7 days to fully water cure. bud washing helped get rid of a lot of extra that stuck to them outside.

Went away for 4 days so I watered them gently before I left. Because I'm using a cheap fan to input air in the closet some mold has appeared on the soil, but it was easy to remove with a spoon.

Another week has flown by! The girls are doing great, cruise control this week as I have just been monitoring RH and temps. Trying to keep them as low as possible, I’ve been getting as low as 74 during the day and 68 at night. I finally took a look a look at the trichomes with my jewellers loop, lots of cloudy, and a few amber around the leaves and top colas, but still lot’s of clear trichomes. I’ve ordered myself a wireless/usb digital microscope to assist with the process, and looks like it will be here just in time to determine harvest day. 😎🎄 I started by eliminating the nutrients at the beginning of the week. I typically allow for 3-4 pure water feeds before I harvest, and at the rate they have been drinking, this should be enough to get through the 7-12 days they have before harvest. I don’t flush, but rather “rinse” with normal water amounts, allowing the plant to use up the remaining nutrients in the soil. This also allows me to recover most of the soil from my grows and reuse ♻️ with other soil mix. There has been great debate and a great deal of bro science out there for many years, but the recent studies suggest there is no difference in end result when it comes to flushing or using nutrients right until the end, if a proper dry and cure is performed. What do you think? What do you prefer to do? Thanks for reading this far, leave me a comment with your preferred method 👊🇨🇦❤️

Greetings to any helpful advice

I started the GSC seeds from HSC by soaking in a glass of water overnight then planted in coco coir under a humidity dome in my veg tent. I will plant them in flower box in a couple weeks when they can handle the feed that my BB clone is on right now. On day 5 my 2 other Gsc seeds rotted perhaps too wet but I have one good remaining for this run. I started White widow seeds and will run 2 phenos. Gsc is looking good so far.

on essaye de palier aux carencesl

Flowers are starting to pack on weight, colors are starting to show and this plant is super sticky. Can't wait to see how she finishes

Well it’s weeks 11 and I graduated from auto flowers although I miss there convenience I’m ready for the big times and I want to grow some regular trees. On one side I topped 2 into 4 bud spots And the other side I fimmed her and I’m stretching her around nuturally

update day 32.. I watered and did low stress training with parts I printed from a 3D printer.