Likes
Comments
Share
Giorno 7 È incredibile come sia riuscito a fare più danni del numero di giorni delle piante. Partito nei vasetti da 0,4l sotto 250w le piantine mi hanno strechato troppo e ho dovuto travasarle per reinterrarle un po' (problema secondo me dovuto al bulbo ormai vecchio). Ovviamente si sono bloccate e questo giorno 7 è come se fosse un giorno 4 Le due zombie Kush sono quelle che sembrano aver accusato di meno Le due Rainbow Belts ferme due giorni si sono riprese oggi Milk Monkey benino Baker Delight bloccata Non le tocco per almeno 20/25gg per poi travasarle nel vaso definivo. Ci vediamo settimana prossima sperando si siano riprese un po
Likes
50
Share
@PapaBlob
Follow
Pour moi c'est du jamais vu. 😮 Effeuillé elle fait 530g. Et oui la vérité sort toute nue de ma tente.🤣 Ci elle tient ces promesses en gout et puissance.. Mmmm.. c'est de l'or en branche. 👍
Likes
2
Share
Soaked the seeds in distilled water for 15 minutes. After I put them on wet cotton pads and sealed those in Mylar bags. I placed those bags on top of my radiator. I made sure it is not running too hot. I don't really care about yield; I just want to do a little project inspired by a YouTuber called Weed in a Pot. I just want to see if I can bring it to the next level with this setup. I already switched out the light for the newer evo dimmable version since it was to strong. Also drilled a few more thicker holes in the bottom for better cold air intake.
Likes
15
Share
Estoy intentando encontrar el balance entre cortar hojas y no cortar... tengo que poner a la California gold en la tienda. por qué decidí germinar y añadir más plantas al cuarto... gorila auto se queda afuera y vemos que pasa ( se supone que es auto y estaría bien) Huele muy bien no puedo esperar para poder fumar estas hermosas plantas que fueron mi primer experimento hidro y creo que hidropónico es fácil y muy fructífero!
Likes
2
Share
Likes
17
Share
@Hashy
Follow
Week 6 Light cycle=18/6 Light Power=120w 50% Extractor controller settings High temp= 25c Low temp= c Temp step=0c High Rh= 56% Low Rh= % Rh step=0% Speed max=8 Speed min=2 Smart controller settings (during lights on). Lights on=06.00am Radiator on= below 21c Radiator off= above 22c Smart controller settings (during lights off). Lights off=00.00am Radiator on= below 18c Radiator off= above 19c VPD aim=0.6-1.4 DLI aim=35-40 EC aim=1.9 PH aim=6.2 Fri 26/1/24 #1 (Day 36) 📋 defoliate lower leaves that hardly get any light. Sat 27/1/24 #1 (Day 37) 📋 H=42cm D=39cm DLI=32.5 Raised light about 10cm Increased light power to 140w H=42cm D=49cm DLI=30.1 Sun 28/1/24 I have decided today is going to be the last day of veg before I flip to flower. Lights will have come on today at 6.00am and go off at 10.00pm, they will get 14hrs light today and tomorrow will be day 1 of 12/12. 💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧 Method= automatic Feed=Veg nutes. Neutralise=0.1ml/L Silicon=1.0ml/L Calmag=1.0ml/L Terra grow=4.0ml/L Roots=0.2ml/L Easy Ph down=0.125ml/L Ec= 2.05 PH=6.1/6.3 Time start=12.00pm Finish time=13.45pm (11×5 minute runs with 5 minute gaps) Total flow rate=181ml/min Flow rate per plant=45ml/min. Total volume made=12L Total volume left=2L Total volume used=10L Volume per plant=2.5L (Est) Runoff. Total runoff=1L Ec=2.7 PH=6.1/6.3 💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧 #1 (Day 38) 📋 With no information for flower time I'm going to have to guess she will be finished in 45-60 days. I removed quite a few lower nodes that probably won't break through the canopy, they where ideal candidates for clones. Light cycle=12/12 Light Power=140w 58% Extractor controller settings High temp= 25c Low temp= c Temp step=0c High Rh= 56% Low Rh= % Rh step=0% Speed max=8 Speed min=2 Smart controller settings (during lights on). Lights on=10.01-21.59 Radiator on= below 21.5c Radiator off= above 22.5c Smart controller settings (during lights off). Lights off=22.00-10.00 Radiator on= below 18c Radiator off= above 19c Mon 29/1/24 Lights on at 10.00am off at 22.00pm #1 (Day 39)(Day 1 flower) 📋 H=45cm D=46cm DLI=23.1 At 9.00pm increased light to 150w H=45cm D=46cm DLI=24.0 Tue 30/1/24 #1 (Day 40)(Day 2 flower) 📋 Wed 31/1/24 #1 (Day 41)(Day 3 flower) 📋 H=48cm D=43cm DLI=28.4 🚿 foliar sprayed (Sumo Boost 2ml/L). Thur 1/2/24 💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧 Method= automatic Feed=water Neutralise=0.1ml/L Roots=0.2ml/L Easy Ph down=0.ml/L Ec=0.2 PH=6.6/6.6 Time start=12.00pm Finish time=13.45pm (11×5 minute runs with 5 minute gaps) Total flow rate=181ml/min Flow rate per plant=45ml/min. Total volume made=14L Total volume left=4L Total volume used=10L Volume per plant=2.5L (Est) Runoff. Total runoff=1L Ec=2.0 PH=6.1/6.2 💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧 #1 (Day 42)(Day 4 flower)**** 📋 H=50cm D=41cm DLI=29.0 Lifted light and increasd power to 196w. H=50cm D=50cm DLI=29.5 She is doing great, has a nice height and shape to her. No problems still. She has been under 12/12 for majority of the week. Back soon. Take it easy.
Likes
8
Share
@TeaTime
Follow
Fastberry Auto is truly a gem among autoflowering cannabis strains! Its rapid growth, delightful berry-like aroma, and beautiful purple buds make it a joy to cultivate. The sweet and fruity flavor is a treat for the senses, and the balanced high leaves me feeling creatively inspired and deeply relaxed. A must-try for any cannabis enthusiast, whether you're a seasoned grower or just starting out! -
Likes
14
Share
Decided to combine all my tents diaries (Wanted to have single strains for contests but its just silly with a scrog going) Great week - All the plants have been through some LST to get the canopy more flat as the back side has more sativa dominant plants. All handled LST really well + SCROG net is up for next week. Flipping to 12/12 this week after a defol + taking clones of each plant for my Phenohunt (Looking for bud with the most bag appeal EX: purple/blues and golden colours that are not usually seen + a good strain to grow in a scrog)
Likes
1
Share
@fabialien
Follow
Semana del 9 al 15 de septiembre 2024. Estas Autos BSF van con todo, muy vigorosas, excepto una blueberry y una Orange Blossom que van un poco lentas.
Likes
44
Share
Well today is 20 I topped her 2 days ago and as you can tell this girl is very happy very healthy and she is rocking and rolling.. she's in a 1 gallon for now and a week or two I'm going to transplant her into a larger pot maybe a 3 gallon maybe a four we'll see but for this girl I am not using organics I'm going back to my old formula and I'm expecting or hoping at least to pull a half pound off of this girl because this is a strain I really want a decent amount of... A huge thank you too Zamnesia Seeds for the opportunity to showcase their genetics which so far have been awesome.. as you can see this is the plant from a one seed pop, I didn't pop three seeds and pick the best plant so I'm very pleased with the results thus far.. this girl just wants to grow and grow and grow.. I highly recommend you guys checking out Zamnesia Seeds as they have everything from seeds to smoke shop needs they even have THC a flower of some of the strains they sell .. they even have kratom to mushroom gummies to rolling papers to absolutely anything you can think of large selection of bongs and the best part is they have an amazing loyalty program called the Tribe .. are definitely worth three or four minutes of your time to check them out for yourself.. this girl's doing amazing just like the watermelon candy autoflower that I'm growing by them.. so far I'm very impressed with their genetics.. hope everyone is doing good and I hope everyone's girls are doing as good as this one.. God bless and happy growing ✌️😎 https://www.zamnesia.com/us/
Processing
Likes
10
Share
Simply planted the seeds a half inch below soil and watered them in... they each sprouted within 3-4 days.
Likes
13
Share
Week 9 day 1 video pheno. Gonna chop this week Week 9 day 7 well chop this weekend so on week 10 Day 1-2. Just waiting on a light to reveg one. Everything is magic
Likes
17
Share
@Fishcake
Follow
The girls got the chop last Friday having a bit of bother with humidity at 70% at 23 c but I can get it down to 60% humidity but the temps drop to around 16 c I'm also attempting to reveg the zupreme just incase its nice lol I already have a baklava reveging now will make a diary for those tomorrow
Likes
47
Share
The cannabis strain Grape Guava can be a purple strain, depending on its specific phenotype and genetic makeup. While not all phenotypes of Grape Guava are purple, some variations, such as the Zatix Grape Guava, are noted for their striking purple appearance due to the genetic expression of anthocyanin pigments. https://www.youtube.com/watch?v=cKdVmdoKJ5k In a garden of green, Grape Guava gleams, With its fruity aroma, enchanting dreams. Clusters of grapes, guava's sweetness ignite, A strain so divine, in purple and white. Euphoria whispers, a lush fruity haze, Grape Guava's embrace, a tranquil daze. Off and away.@1400ppm. The increased CO2 allows plants to thrive at higher temperatures, which in turn necessitates higher humidity to maintain the ideal VPD for healthy growth and transpiration. 80F -5F = 75F LST with 70% RH = 0.72 kPa. Higher temperatures and humidity promote rapid growth, nutrient uptake, and photosynthesis while maintaining a lower stress level. Temperature influences the rate of enzymatic reactions involved in aerobic respiration. Enzymes, such as those involved in glycolysis, the Krebs cycle, and the electron transport chain, work most efficiently at an optimal temperature range. In low temperatures, enzymatic activity will slow down, thus reducing the rate of aerobic respiration. In high temperatures, enzymes can become denatured, thus impairing their function and stopping the process of aerobic respiration. Glucose is the primary fuel for aerobic respiration. The rate of aerobic respiration increases with the availability of glucose, as it is the starting point for glycolysis. If glucose levels are low, cells may rely on alternative energy sources such as fatty acids or amino acids , but these processes may yield less ATP or be less efficient. To determine this effect, carbon dioxide volume was measured (as carbon dioxide is an output of aerobic respiration) 18/6 with the 6 being IR. The near infrared (IR-a) borders around 700nm up to 1400nm @ photon par flux density of 1.8 instead of darkness, keeping temps overnight a neat 77F-80F. Think of my tent as a lung. What goes in must come out. When the rate of air going out exceeds the amount of air coming in, it creates a negative pressure. Tent concaves (bends in). If set up correctly, your RH will begin to drop slowly to the desired level you set, and the extraction turns off when it reaches desired% RH. The plant, as it performs cellular respiration, will always be releasing more water into the air, so the RH% of the tent overnight will always increase, so long as oxidative phosphorylation is occurring. As soon as the RH% creeps back up to 55%, the extraction turns back on, over and over. This creates a strong pressure differential which will work wonders on your grow. Replicating high and low-pressure fronts in nature. Critical for oxygen diffusion at the critical time of peak cellular respiratory function.. Moisture will not transfer from a saturated atmosphere to another if that air is already at or above its saturation point, meaning the air can't hold any more water vapor. Once I understood that water is produced as a by product during cellular respiration, specifically at the very end of the electron transport chain (ETC) where electrons are finally transferred to molecular oxygen, the higher the RH of the air, the more resistance there is for more moisture to be added to that environment, and effects the ease with which it does so. But none of that water comes from the pot; it's pulled from the air. If you run high daytime RH, your medium/pot is 100% reliant on transpirational root pull to move water. ZERO evaporation happens across the atmosphere if the tent air has high RH%, the medium cannot release its water through evaporation. Once a canopy develops, light no longer slowly wicks and evaporates from the topsoil. The Soil-Plant-Atmosphere Continuum (SPAC) describes the continuous pathway and process of water movement, driven by a gradient in water potential, from the soil, through the plant's roots, stem, and leaves, and finally evaporating into the atmosphere through transpiration. There is evaporation, there is transpiration, and then there is evapotranspiration; Evapotranspiration (ET) is the combined total of two processes: evaporation (water lost directly from soil and surface water into the atmosphere) and transpiration (water released from plants to the atmosphere through their leaves). Evapotranspiration represents the total amount of water that moves from the medium into the air. There is no such thing as a medium with too much water, only a medium that retains too much for too long. The water must always flow efficiently from one atmosphere(Medium) to another(Air) in a timely manner. Moisture is a critical factor for bacterial growth and decay. Dictating how long it's allowed to sit in any one location for any given period is a key preferred control. To ensure a net reduction in a bacterial population, the rate of removal (ET) must exceed the rate of bacterial growth (decay rate), which is often modeled as a growth rate for the specific bacterium under the given conditions. By optimizing daytime VPD, we also optimize conditions for bacterial growth to explode exponentially above 77°F.. If water is allowed to sit in a medium without an escape within a timeframe, nothing good will happen. IF High RH is maintained overnight as well as during the day, placing 100% of water movement at the behest of daytime transpiration, roots can only pull where they can reach, and if soil is compressed above a certain point, moisture will become trapped in a medium with no way of moving day or night. This will begin the countdown for decay to take hold. When water stagnates in a medium, it loses oxygen, creating anaerobic conditions that foster the growth of harmful microorganisms like bacteria and fungi, which can produce toxins and disease vectors. Thigmomorphogenesis, the process by which plants respond to mechanical stimuli like touch by altering their growth and development, results in significant morphological changes to improve survival against mechanical perturbations. This complex response involves sensing touch and initiating physiological and genetic responses, leading to changes in form and structure over days or weeks. The process is triggered by physical forces such as wind, rain, or touch. Plants adapt to these stimuli by changing their shape and structure, which may include slower growth, thickened stems, or altered leaf development. Plants possess sophisticated mechanisms to detect even subtle mechanical stimuli and initiate responses. A variety of molecules, including calcium ions, jasmonates, ethylene, and nitric oxide, are involved in signaling these mechanical inputs. Touch can induce the expression of genes that encode proteins for calcium sensing, cell wall modification, and defense mechanisms. A plant exposed to constant wind may become shorter and sturdier. A plant that is touched frequently might grow more slowly to conserve energy and develop thicker cell walls. These changes increase a plant's resilience and ability to survive in harsh environments. Let's get Thiggy with it.
Likes
38
Share
******** Week 7 - January 20 to 26, 2020 (Days 43 to 49 from germination) She continuers to impress with her resilience as I have thrown a couple of curves at her.......but she continues to fatten and grow her buds😎 It was also not without learning though and thats what is so cool about growing this plant.......you always seem to leave a grow feeling like you could do even better next time and therefore challenging yourself to do better......and have dab while doing it😂 Not sure if I have a little different pheno but if I ran her again I would find a way to train her out wider. 5 gal pot diameter idea........maybe don’t fill with as much medium? Again, simply to keep light hitting all the lower sites. Where does the “XL” come into play as well I guess. Removed branches early on that were low. This grow, her narrow leaves have allowed a lot of light down below but it will be felt in a little less yield.....think the pH got a little high....or potassium excess......Terpinator too early? If left to a single cola she would be tall and have a huge cola I suspect......Gorilla Grow with the extension type of potential! She has loved the water feeds. Missed out bit by backing off of the CalMag a bit too much.....stems say deficiency that but leaves show toxicity? (Back to that you always feel you can do better thing😬) Got a little crazy with the PPM and saw tip burn in week 7. Gave a quick little flush with RO water and Sensyzime to clean up the roots of the salts. Didn’t get crazy though because it was just the top leaves burnt. Been building the medium up to this point so don’t want to wash it all away just yet. She didn’t claw down and over night appeared to still keep moving forward with bud growth. I did notice a small amount of hairs starting to turn red by weeks end......likely won’t be long before more are red and we go to flush👍 (Make it to end of week 8??) No rush though.......still lots of room to fatten up yet. In the week a head there will be the last push to get her medium in as good a shape as my skills will warrant. I want to get a good 10 + days of flush but her leaves are going to finish dark from what I can see. Run-off has been reasonable though so will keep fingers crossed 😄🤞 Little more detail.... Jan 20/20 - Day 43 - Drinking lots right now, close to 4L per day, so 2L plain water only in AM. 6.2pH,. - Feed in PM was light as well. Sensyzime @ 2ml and LW8 & Rezin @ 1.5ml only. 2L given with 75ppm. 5.9pH - She was given a good feeding yesterday. - Buds sites are stacking.......she is making me 😃 Jan 21/20 - Day 44 - AM - 3L with Dual Fual A&B @ 1.5ml/L. 725ppm and 5.9pH. - PM hit her again - full feeding minus Rhino Skin, Sensyzime and Vitrathrive and VeloKelp. 2.5L 1000ppm and 5.9pH. - Runoff - 1100ppm and 5.9pH. - top leaves were droopy so the extra feeding in the evening. Jan 22/20 - Day 45 - Backing off quantity a bit and down to 2L feed in PM. Her pot was still fairly heavy. - Mass & Terp @ 3ml, Rezin & LW8 & DF @ 1.5ml, CalMag @ 0.5ml = 1300ppm - Very perky today....standing up all the way down the plant. Liked the feed yesterday. *******should have reduced this PPM feed......you want to push when you see potential😕 Jan 23/20 - Day 46 - Supplemental feeding only today. Happy so don't rock the boat :) - Sensyzime @ 2ml, LW8 & Rezin @ 1.5ml = 80ppm 6.1pH - 2L only today.....still some weight to the pot Jan 24/20 - Day 47 - Nute burn on Green Poison’s tips seen today. - Flushed through 7L of plain RO water pH to 5.95. - Runoff: 325ppm and 5.9pH. - Followed right away with 2L more water with Sensyzime @ 3ml/L - happy and praying in the evening......little surprising actually👊👌 Jan 25/20 - Day 48 - 2.5L of full strength feeding for this week. - ppm for that was 1275 so watered down to 1100ppm.....only need 1ml of base nutes at full strength to hit roughly 1,000ppm. - Runoff: 600ppm & 5.95pH - Swear her leaves are bigger, more mass today!! Still narrow and dark though. - she is 30” x 30” now Jan 26/20 - Day 49 - Feed was full strength one for the week, 1150ppm 6.1pH. - Removed some more leaves today. - guessing only another 1.5 weeks of feeding. Happy growing fellow enthusiasts and thanks for the time to read🙏🙏
Likes
4
Share
@Hommero75
Follow
The 2nd week was great for the plants. Specially Banana Purple Punch and Forbidden Runtz They stretched and grow without no problem. I'm excited for week 3. I LST them, I did some defoliation and they got fed with Goldleaf feterlizer and I added mycos chum and cal-mag to the mix. Let see how they do.
Likes
7
Share
These are some amazing genetics they just keep getting Frosty or every week every day more and more trichomes
Likes
1
Share
Buds are getting ripe. Pistils are 75% brown and trichomes on buds have amber and are cloudy and sugar leaves have 30% amber. Flushing next week for a few days then chopping.
Likes
5
Share
3. November Alle drei Pflanzen weiterhin topfit. Trauermücken aufgetreten. Habe das abgelaufene Päckchen nematoden für die runtz genutzt. Hoffe es bringt was 4. November Cookies Gelato hat den harten Mainlinecut bekommen. Spitze wurde entfernt, Seitenteile wurden direkt danach abgeschnitten. Sie wird’s schon wegstecken. Tropimango und runtz geht’s gut :) Cookie gelato hat bereits wenige Stunden später die Blätter wieder hoch gestreckt. Stagniert. 5. November Alles gut. Die Schnitte wurden gut verkraftet. Triebe wachsen wieder Cookies gelato ist nun 21 Tage alt. Tropimango ist nun 18 Tage alt. Runtz ist nun 7 Tage Alt. 7. November Cookies gelato wächst. Sobald die Klammern da sind wird sie runtergebunden Tropimango hat schnitte und Lst bekommen. Topping werde ich noch abwarten. Runtz wächst 8. November Cookies gelato hat LST + mainlineschnitte erhalten. Wurde nicht mit gießen kombiniert da ich gestern gegossen habe. Tropimango erneut LST. Runtz wächst. Sieht aus als würde sie langsam ins Wachstum wechseln. Erster Triebe am einzahnblatt kommen. Dreizahnblatt erst frisch entwickelt. 9. November Cookies gelato wurde das erste mal zusätzlich mit Sugar Royal und calmag versorgt. Hab’s davor vergessen 😅 Shit Happens. Wurzeldünger gibt es konstant weiter. Runtz wurde mit wurzeldünger und calmag versorgt Tropimango hat noch sehr feuchte Erde. Keine Ahnung wieso.