_____Week 6 | Day 42-49 ______ Day 42 - 48 🌞 ------ Not much happened this week. I had little time for pictures and documentation. This week I just made sure that the new branches always get a lot of light and are not covered by other leafs. The plants have not grown much, because I constantly stress them and push them down. All new shoots that grow to size were topped, in the middle area of the plant, to keep everything nice and even Day 48 🌞 ------- each Plant 2 Liter...gluck, gluck, gluck.... ____________________________________________________________________________________________ Light - 18/6 h - 400 Watt 60% Dim. PPFD - 600 - 650 µmol Temp. - 24° Hum. - 70 % RLH

Good week, Cm smells like grape drink, delicious

Moving right along, each girl is on her own pace. Tent was so crowded I had to remove the heater therefore I bought a bigger tent and will use use this one for drying. Thanks for looking..

Growing was quiet hard as it just wouldnt respond will with training technique such as super cropping she hardly stretched when switched to flower and grew slow during veg but can not say till I do another run and do things different and as it was my.first time also growing from clones

Hello my friends 👨‍🌾👩‍🌾, I'm still in gd jail, since 1 month, Thanks for your coms and likes, can't reply you... This week Buds are more and more fat 🌲🌲❄️❄️🍌🍌, smeel like a banana 😍😛 💦 I've given 3x 2 l/plant Water + terra flores + Pk 13/14 Water + Cannazym + Sugar Royal Water Only PH@6 Lamp @75% I'm looking for a 120x60x150, to put the fc3000 inside and use only one lamp and 1 tent, cause energy cost, and optimized my grow space, it will be easiest for my air system.. I'm waiting all plant will be harvested to don't contaminate the futur plants with thrips. See you next week and have a good week end my friends 🔥👨‍🌾👩‍🌾 Thank to Mars Hydro and @marshydrococo2 for sponsoring the FC3000 ❤️❤️, as well as @Fast_Buds for sponsoring the Seeds ❤️❤️ If you want a litle discount on your Mars Hydro order, add this coupon to your cart, "Ju_Bps" Thanks community for follow, likes, comments, always a pleasure 👩‍🌾👨‍🌾❤️🌲 Mars Hydro - FC3000 https://www.mars-hydro.com/fc-3000-samsung-lm301b-led-grow-light 42 Fast Buds - BANANA PURPLE PUNCH🍌🌲 https://2fast4buds.com/seeds/banana-purple-punch-auto

Topped her again! I came back to this beauty after almost 10 days of feeling like trash. She was getting the minimum amount of attention, but has stayed strong. I have a couple of Autoflowers to finish up, then I will be transplanting her once she has recovered from the topping to a 7 gallon fabric pot. I will probably try to run a SCROG and see if I can fill my 2x4 tent with the one plant.?🤔 Conditions have been good, 76 degrees and 60% RH. Temps at night are still pretty cool so I kept the small heater going for now. I will start bringing the EC up a bit over the next couple of weeks to see if I can get her to really feed, she has shown no signs of nutrient burn yet 🤞Happy Gardening 🇨🇦👊❤️💨

The plants have already been topped. Today, on 25-05-2024, two large leaves were removed, covering the sprouts. The LST was done at the same time.

Day 71 Update: Watered both plants with almost a gallon until runoff. Water was just plain pH balanced water. Plant #1 has 5 days left on flush and Plant #2 has 11 days left on flush. Although with my tent filling up, I will probably harvest Plant #1 tomorrow as I don't think 4 days of being in there will make a difference in the end product. Day 72 Update: Harvested Plant #1 today. Plant #2 has 10 days left on flush. Day 74 Update: Watered plant with 3/4gal of pH balanced water until runoff. Plant #2 has 8 days left on flush. Also, added another stake to help support a heavier branch. Day 76 Update: Placed buds from Plant #1 in jars to start curing...maybe a little bit too long drying, but if that's the case I'll toss a boveda pack in. Plant #1's yield was 57.2g or 2oz 1.2g. Plant #2 will be harvested sometime next week and I will update the harvest page as soon as buds are dried and weighed.

Chopped And Hang drying I lost count of thow many days in flower But I know its over 100 days I'll be making canna oil with coconut oil And canna oil with MCT oil

A semana de maior desenvolvimento das meninas.

So not nitrogen deficiency. It's light burn. Being that my lights at the highest it can be I am starting to let it have some rest at night. 20/4 now. Already the leaves are less brittle. Ph is balancing. Buds are fattening up nicely.

Week 10 D70 coming along nicely, still has a ways to go. As she only started stigma 20 days ago, well in or around that. For 5 nodes in total she is doing really well you can see all the energy is focused on making nice dense close together buds that should all form into nice big long colas, well to me, that's the way it looks like it's growing. Only flowering 20days looks a lot longer than that right? What do you think? 19/3/22 As you can see I have the RH as best as I can get in my grow room, I've installed the smart fan and inserted the sensor giving me 57%RH/75F in the tent, with the light off, it's rather hot today, much hotter than normal, it's normally 21c in my room it's 24.5 today. RH is at 50% in room, hopefully by installing my old intake fan in the lowest part of my tent and suck out 80% While 100% gets blown in on top will bring the tents RH to the same as the room, that's the hope anyways. But 57%RH is still okay, not optimal but not too bad neither. Thanks for reading, drop a like or comment so I can do like wise on your diaries. 21/3/22 So, I tried out my new method. Of having my smart intake fan suck in 50RH and a bottom intake fan at the end sucking out older air at a lesser speed had it running for 8hrs, no change in humidity whatsoever just dropped the temp by 1.5c. I think the fact I have a 70x70 with so many plants has set the RH and thankfully it's not what it was which was touching on 80rh at some days. A bigger tent and I'll really be able to dial in my grows now I have all the tools to control RH/TEMP from S/H. For now 57%RH when it's low and 62% when the lights are on for a few hours. Stays around 57-60% atm for around 85% of the time. Temp is constant and doesn't change without my control within a range of 4-6c change difference, this number I have no problem in changing and I'll be making my tent a lot cooler after this wk ends. I'll be keeping her at 18c with lights off and 28 with lights on. As for this plant she is a little gem. For 5 nodes she has a lovely shape and in this plants case there really is nothing that should be done to it at this stage, just let her beauty unfold. gottagrowsometime

Week 3 of flower

Jackie is all flushed out shes fat frosty sticky and stinky she smells like oldschool skunk shes stacked great buds could be denser but i expected sativa style buds with an indica coating of resin and thats exactly what she is so no complaints looking forward to the harvest report thanks for reading happy growing guys

On day 1 I adjusted the reservoirs PH from 6.4 to 6.0. The tallest cola is 5.5" from the light. Lower colas are mostly 9"-10" from the light. On day 2 the reservoirs PH is 6.1. The tallest cola is 5" from the light. Lower colas are mostly 9"-10" from the light. On day 3 I adjusted the PH of the reservoir from 6.0 to 6.3. The tallest cola is 4.5" from the light. Lower colas are mostly 8"-10" from the light. I did my last major defoliation in order to bring more light and air flow deeper into the canopy. The plants are progressing as expected. No smell yet and the pistils are showing more each day. On day 4 I adjusted the PH of the reservoir from 6.4 to 6.1. My mini dehumidifier was emptied after being 3/4 full after 5 days running. My tallest cola is 4" from the light. Lower colas are mostly 8"-10" from the light. On day 5 I adjusted the PH of the reservoir from 6.0 to 6.3. My tallest cola is 3.5" from the light. Lower colas are mostly 8"to 10" from the light. The plants buds are growing in size with more pistils showing every day :) On day 6 the PH of the reservoir is 6.2. My tallest cola is 3.5" from the light. Lower colas are mostly 7"-9" from the light. It looks like the stretch has finally stopped. I experienced a Runaway with my blumat on my right side plant. I reduced the flow of that blumat by 1 carrot and will monitor the situation going forward. After adding my carbon filter to my exhaust I realized it was drawing the heat from my box causing in proper heating. I will try to reduce the air flow of the carbon filter to make it easier to keep the heat in the grow box. On day 7 the PH of the reservoir is 6.2. My tallest cola is 3.25" from the light. Lower colas are mostly 7"-9" from the light. I did one last major defoliation on day 21 of flower to improve airflow and light penetration keeping only the top leaves of each cola.

What’s uppp! 🖖 Weekly update… 🔥 Day 55 | Flower Day 20. The girls were ready for a little defoliation today, so I gave them a clean-up. They’re looking great now! 😎👌 Looks like we’re on track for a tent full of fat colas! 🌿💪 Good luck and happy growing! ✌️🍀 ____________________________________________ Servus! 🖖 Tento týden pažák…🔥 Máme tu 55 den, 20 den květu. Holky si dnes řekli o DEFO, tak jsem to trochu pročistil. Myslím, že takto holky v cajku. I tak to vypadá na fajne full houses! 😎👌 Ať se daří! ✌️🍀

420 Fastbuds Week 7 Gorilla Zkittlez Auto What up grow fam. These two lovely girls are growing absolutely beautifully. Staying on the shorter side but wow have the flower sites grown. The smell is strong and sweet. I upped the tds to about a 1000 but will dial it back down in the up coming weeks as they finish up. All in all Happy Growing

ALL THESE PHOTOPERIODS WILL GO IN THE 8X8 TENT ONCE THE AUTOFLOWERS ARE CHOPPED AND I WILL SWITCH THE LIGHT TO FLOWER THEM IN THERE FOR MORE ROOM FOR EVERYTHING MARS HYDRO VISIT: www.mars-hydro.com www.marshydroled.ca PROMO CODE: rocknroll VISIT THE ALIEXPRESS STORE: @marshydro_aliexpress Instagram: @marshydropenny Thanks for taking the time to read and check out my diary🤜🤛 TS3000 FEATURES: WIDEBAND SUNLIGHT FULL SPECTRUM LED GROW, Infinite close to natural sun light, suit for all plants whole stages indoor growing, rapid plant response from seed to flower, achieve maximum quality and quantity, much better than traditional HPS grow systems. HIGH REFLECTIVE & NOISE FREE-Fanless LIGHT BOARDS design will make your growing life easy and quiet, quickly heat dispersing material aluminum reducing light lost to aisles and walls, increase the light intensity up to 20%, allowing your plants receive more energy and without burning your plants for maximum headroom. HIGH EFFICIENCY ENERGY SAVING PLANT LIGHT, high-power NEW LED grow, Compares to traditional 3000 watt HPS lamp and other brand led grow light while only 450 watts true output with 1016 LEDs, more scientifically and energy-efficient! Perfect for 5' x 5' veg stage, 4' x 4' bloom stage, higher intensity in a MARS HYDRO grow tent, reflective area, or by crossing over using multiple TS3000. BOOM YIELD LARGE GROW LIGHT, NEWEST SMD LED technology provide highest PAR/LUMEN output(1095.6umol/), makes you get 30% higher yield compare OLD led lights, can get max yield at 2.5g/watt, less pay but get more yield, bring a amazing grow trip to any home grower as it beams huge amounts of light energy to plants below. COMMERCIAL LED GROW LIGHT, Updated easy dimming & daisy chain function, main light controlled, especially come with two waterproof and dimmable Mean Well Drivers, auto sensing power supply works on both 120VAC and 240VAC and 277VAC, suit for Large Rooms and Commercial Setups. Low Energy-Consuming LED Grow Light: Consuming 300w and also mounted with 1016 chips, TS3000 has the ability to replace a 450w HPS light while reducing 40% power intake. High Efficiency LED Grow Light: With overall light output PPF 343umol/S as well as amazing PPE 2.3 umol/j, it's 50% even more photon efficient and can assure a 30% more return than the old HPS/MH lights. Patent Highly-Reflective Hood Shape: The reflector design on TS3000 is patented, which can effectively gather the light dispersed in all directions to enhance its light intensity as well as assist plants in absorbing more light. Full Spectrum Plants Favorite Spectra: By the unique mix of spectra that makes most light in the 400-700nm waveband, incredibly conducive to plant photosynthesis. Adequate IR(730-740nm) is additionally consisted of in the range to generate larger buds. Dimming And Daisy Chain Feature Available: Upon an independent dimming button on the external driver, backing 0-100% settings adaptation and up to 30 LEDs daisy-chained in a group, it supplies different light levels for various plant stages meanwhile saving energy. Safety Certifications And Service Warranty: CE, ETL, RoHS, UKCA security certifications accepted, 50,000 hours durability, 5-year service warranty, and local after-sales repair 5x5 GROW TENT: LOCK ALL LIGHT INSIDE MARS HYDRO Indoor Grow Tent interior is made of diamond mylar which is highly reflective. (Other brand's mylar and reflective rate is as low as 50%, won't provide efficient light. )MARS HYDRO 1680D canvas, being double stitched, it is tear proof and has perfect light locking. Mars Hydro's grow tent keeps 100% lighting beams inside and helps your plant absorb more lights. EXTRA-THICK --No light leaks or rips at all DURABILITY GROW TENT Stable metal corner adapters and poles are the trustful supporters of the tent, standing sturdy, neither rusting nor paint-falling, quick easy tool-free installation. Mars Hydro's heavy-duty metal zippers, with double layer black lining, are the best on the market which create a light-proof seal EASY OBSERVATION FOR YOUR PLANTS. Special observation windows are made by double layers of cloth. Observe the growing conditions of your plants without opening the tent and avoid disturbing plants. The observation window also serves to dissipate heat and ventilate air AUTOMATIC 6 INCH EXHAUST FAN KIT W/ CONTROLLER: Mars Hydro 6'' Inline Fan uses a mixed-flow design to maintain peak performance in a high static pressure environment. GROW TENT FAN: MARS HYDRO inline fans are designed to ventilate hydroponic grow rooms, transfer heating/cooling, cool AV closets, and exhaust odors. EFFECTIVE VENTILATION: Variable speed controller for easy fan speed adjustment. Optimal ventilation for your planting. LOW NOISE LEVEL: Durable plastic fan housing and blades for extremely low noise(32dB-A); create a truly quiet growth environment. EASY INSTALLATION: Removable duct ends with locking tabs for quick removal and easy maintenance and a cord length of 4.9 feet for hassle-free setup. This grows tent fan with a controller for easy fan speed adjustment. BASIC PARAMETERS: Ventilation exhaust fan size: 6” | Dimensions: 315mm*225mm*210mm. | Weight: 2.7. | Airflow: 402CFM | Noise: 32dB-A | Bearings: Dual Ball.