#beginning of flowering 09/04/19 #04/13/19 update of photos and videos are from the 5th day of flowering

End of week 4 , huge difference each week. Buds started fast, strong purple genetics showing instantly. Can't wait to see what happens. So far everyone is healthy and happy

This is my first ever grow and thought I'd document and also seek advice. Neurodivergent grower here, seem to have gone overboard for a first timer. Running a drain to waste system through coco/perlite (70/30). Using 1.2 gallon pots from The Bucket Company. Hooked to a water bubbler irrigation feed from reservoir. The reservoir is a makeshift mobile chiller aha. Seemed a good a idea but could only hold 3-5 gallons at a time. Will need to either fork out on a water chiller with bigger reservoir upgrade or think or something. Under the reservoir we have the EZrun-off pump by The Bucket Company. Essentially a catch tray with a pump inside that automatically pumps the waste out to the desired location when maximum storage capacity is close. Mine runs just over to my kitchen sink.....when I can be bothered to make some holes underneath....I could hide the pipes and make it more stealthy via routing it to the drain pipe works under the sink cupboard. Old drippers where replaced mid veg stage with Netbow halo drippers by Netafim. Achieved a much more uniformed saturation of the medium. My nutrient of choice will be MegaCrop by Greenleaf nutrients plus additionals such as Orca mycorizhae and Myco Chum for the extras... Popped seeds directly to riot cubes on 14/06/24. 3 days later we have sprouts. Purple Stardawg x2 Runtz x2 Strawberry Cough x2

Planten groeien als kool. Wanneer de eerste bloemen vormen, dan ga ik ze ontbladeren. De planten krijgen melasse- en zeewiervoer en wat lavamolen. --------------------Durban----------------- Durban wietzaden komen oorspronkelijk uit Zuid-Afrika en zijn gekruist gedurende vele jaren in de jaren zeventig. Door al deze kruisingen heeft deze soort zich aangepast aan het Europese klimaat. De planten zijn bestand tegen wind, koude temperaturen en schimmels. Ze bestaat voornamelijk uit Sativa en heeft een bloeitijd van 8 tot 9 weken. Voor zowel de binnen- als de buitenkweek kun je een grote oogst met stevige toppen verwachten. Durban kan buiten een hoogte bereiken van 200-300 cm. Durban is een exclusieve Sativa-soort met een unieke, heerlijke geur. Deze soort staat bekend om zijn kruidige, wazige smaak met sporen van anijs, zoethout, citroen en kruidnagel. Dit heerlijke aroma is een van de redenen waarom zoveel kwekers keer op keer voor Durban kiezen. Eigenschappen van Durban wietzaden Hoog THC gehalte Exclusieve Sativa Hoge opbrengst Sterke soort Heerlijk aroma Informatie Durban wietzaden Bloeitijd: 8 – 9 weken Genetica: Durban x Original Thai 70% sativa, 30% indica Planthoogte buiten: 200 – 300 cm Oogstmaand buiten: van juni t/m oktober Opbrengst binnen: 450 – 650 gr/m² Opbrengst buiten: 200 – 700 gr/plant THC: 20% Link naar de shop: https://seedsgenetics.nl/product/durban-poison-gefeminiseerd/

They look super happy, nothing to complain about.

9th week: Wedding Cake auto: I am happy with my grow. She is looking great. I had never seen anything like that. She is 124 cm tall and full of trichomes as you can see in the picture. As advised by an experienced user, i defoliated the damaged leaves. She is looking way cleaner now. I also added Big One as advised I can see some brown trichomes appearing. I hope to see more brown trichomes in the end of this week. Godzilla Cookies auto: She is 76 cm tall and still under growing process. She has way less damaged leaves and is greener than Wedding Cake but way smaller tho. ------------------------ Smell: Strong, If i open the door of my room and keep it opened for a while, anyone in the house will detect it.

FBT5 in Mr. B's has been no trouble at all so far, still moist in there so i've not watered on day 5, spraying the soil with amino, did one foliar this week on day 5. Probably will fix the fan over the weekend so it's pointing straight up. FBT5 is an interesting one, vigorous in many ways, it seems to be working hard below grownd . anyway I'll try to get an in soil pH reading on the Mr. B's asap. but it will mostly be secondary nutrients and co2 from now on.

And one more week up we go, they are growing beautifully under the TSW-2000 from MARSHYDRO, so beautifully that pretty soon i will have to get my hands dirty and defoliate this beauty’s 😁 trying my best to keep my hands still, but knowing my self that won’t last long 😆😅💚 i will keep you guys posted along with what i am doing 💚 apologize the delay, i know today is day 2 from week 2 since i flip them to 12/12 ( one day delay i belive its ok 🤣😆😅💚) just kidding , growers love and stay posted 💚💚💚 Day 14 F and i realized i have 2 leafs showing some disability , i will increase my calmag for my next feeding and keep a close eye on them, not worry about it for now, since 2 leafs out fo , i have nomidea how many 😆, for me its not an issue, but non or less it’s something and its always better to be proactive. I will keep yo guys posted for good or for bad 💚💪🙏 growers love and remember to follow my Instagram account for ever day extra updates and so much more 🙏💚💚💚 Day 16 F And it looks like all is back on track , new leafs are beautiful and the bigger ones also, no more ugly leafs for now, all i did was an increase of 50% on the calmag , they seams to react good to it 💚💚💚 And with and enormous honneur and pleasure that i start collaborating with MARSHYDRO, they wore kind enough and send me a 4x4 grow tent and a TSW2000 for me to do tests and reviews, i got to admit the quality on the materials, the easy assembling, the user manual, even the art detail that came with a bunch of cool stickers, are plus things that can not go unnoticed 🙏💚 Thanks Marshydro for so many details 🙌😉 i will try and post them all in here, but you can follow me on my instagram account https://instagram.com/dogdoctorofficial for every day updates , videos giveaways etc, or in my youtube channel- https://youtube.com/channel/UCR7ta4DKLFMg2xxTMr2cpIg keep tuned 💚💚💚 Thank you MARSHYDRO for having faith in my love for growing , lets make magic together 🙏🙏🙏 Genetics - Cookies Fam genetics - 3x SunsetSherbet Grow tent - MARSHYDRO 4x4 Ligth - MARSHYDRO TSW 2000 @ 100% Food - HAPTUS HOLLAND Filter - vanguard hydroponics Falcon Filters Extraction - 2 x vanguard hydroponics 280m3h Extraction control - SMSCOM Smart MK2 All i grow is medicine for myself, for me and for my best friend with is me 😆 nothing to sell, so don’t even ask 😅💚💚💚 All info and full product details can be find in can find @ https://www.mars-hydro.com/grow-tent https://www.mars-hydro.com/led-grow-light/mars-ts-series-led-grow-light/mars-tsw-2000-led-full-spectrum-hydroponic-led-grow-light https://marshydro.eu/ DISCOUNT CODE - DOGDOCTOR 💚💚💚🙏🙏🙏💚💚💚 https://marshydroau.com/ https://aptus-holland.com/ More info and updates @ https://growdiaries.com/grower/dogdoctor https://instagram.com/dogdoctorofficial https://youtube.com/channel/UCR7ta4DKLFMg2xxTMr2cpIg 💚💚💚Growers love to you all 💚💚💚

On day 3 -4 of 5 seeds have germinated! On day 4 all 4 seedlings were fed 500 ppm veg nutes. On day 5 seedlings were transplanted into 4" nursery pots with myco. I watered them in with 600 ppm of feed. Ppfd 450-500.

Day 43-49 A lot of them are showing signs of going into bloom. Doing their stretch before bloom, so they need more nitrogen before they're done stretching. My own unbiased opinions about deep water culture.I love it.It's got the precision I need and control. If you like something more relaxed, living soil is your thing, but this is mine.I'm enjoying it.Everything's growing people have already done the research.I just gotta apply it.

10-21 - Finally have room to start my new run! Dropped the little Sunset Sherbet Go Fast seed today in some water. 7:00am, it begins!...my days start early lol 10-22 - Cracking open in that water today, but nothing really to report 10-23 - Tail is out! Planted into a puck this morning with a bit of myco. 10-24 - She is up and tall today! - Got her pot ready for planting tomorrow. Went ahead and pre wet the coco with a light feed mix of 1.75ml/gal cal mag, 1.75ml/gal Coco A, and 1.75ml Coco B. Ppm 270 with a ph of 5.8. Will feed this same feed for the next week or so also after planting. Using 3 gal fabric pot, straight coco. ** Yep....It's my turn! Sure, my husband thinks he is growing the 'perfect' Sunset Sherbet right now....but I promise, mine WILL be better! 😁 LOL Two completely different grows though! He's in coco/peat/, I'm in straight coco. He's using Plagrons organic Alga, I'm using Plagrons Coco A&B. He's more 'dialed in', I'm more 'ehhh it is what it is '. He likes to monitor his cats, I let mine do whatever they want. So, he may not know it yet...but the competition has already began!

Sticky Broccoli Auto – Harvest Update Strain: Sticky Broccoli Auto Breeder: Zamnesia Seeds Grower: Little Lilly Farms Overall Outcome This run didn’t hit the mark. The genetics felt unstable and inconsistent across all four plants—each one expressed very differently in structure, growth, and final bud development. Bud quality leaned airy and loose, lacking density, but was heavily coated in resin and trichomes. Visually appealing frost, but the overall structure didn’t back it up. Terpene profile was underwhelming—nothing loud or complex. Mostly a sweet gas aroma, but lacking depth and punch. ⸻ Harvest & Final Week Timeline 4/1 Fed one plant ½ gallon of previous nutrient mix. Very minimal runoff. 4/2 * 1 gallon of premade feed (from 3/31) used * Small runoff achieved * Other 2 plants received straight RO water (not pH’d) * No noticeable change in color or fade on water-only plants 4/3 ¼ gallon of premade feed mix applied 4/4 – Harvest Begins * Cut down 2 plants * Fit both into the Cannatrol for drying * Buds extremely resinous and sticky * Heavy trichome coverage across both plants * Switched remaining plants to straight RO water moving forward Final Feed Mix (per gallon): * 0.5 ml Silicium Bloom * 2 ml MagCal * 4 ml Green Sensation * 2 ml Cocos A * 8 ml Cocos B * 4 ml Pure Zym 4/6 * Purple coloration showing on sugar leaf edges * ¾ gallon RO water (not pH’d) * ~5% runoff 4/7 * ¾ gallon RO water * Minimal runoff 4/8 * 1 gallon RO water * ~15% runoff 4/9 * ¾ gallon RO water * ~20% runoff 4/10 * 1 gallon RO water * ~15% runoff ⸻ Drying & Cure All 4 plants have been harvested, dried, and are currently being trimmed. Final weight will be recorded once trimming is complete. ⸻ Final Thoughts * Pros: * Extremely resinous buds * Heavy trichome production * Good visual frost * Cons: * Airy, low-density buds * Weak terpene expression * Highly inconsistent phenotypes across all plants Overall, this run felt like a genetic gamble that didn’t fully pay off. While the resin production was impressive, the lack of density and terp complexity made this one fall short of expectations.

Eine Knolle der shaman hatte budfäule musste entfernt werden. Hab dann viel entlaubt. Habe Betonplatten organisiert kann jetzt Gewächshaus aufbauen hoffe steht bis nächste Woche. Hoffe Wetter wird besser/trockener + windiger 🐝

Flush time:)))

HEY! the beginning of flowering. and there are many hopes that it will be completed before the end of the competition from Green House! well, everything goes perfectly in ostolny) the trunk gets fat. branches grow longer and flowers bloom)) it is very difficult to understand its size from the photo) but believe me, it is huge. and occupies an area of 80cm-80cm wide ..

Nice easy week just added some Bud Start by future harvest to the mix of nutrients. Little buds are stating now! Can not wait to see how they start looking over the next few weeks!

I came back from vacay. Im harvesting the amensia haze next week!! i’m really excited! i wonder if the painkiller will make it tho. spider mites and thrips somehow got to the plant even though it was inside. and all the pests collectively decided to leave the amnesia alone? Also got new seeds! only paid for 3 lol

6/21: Topped off buckets and adjusted pH to 6.2 6/22: Removed growth that was not getting light. Topped off buckets, adjusted pH to 6.2 6/23: Topped off buckets and adjusted pH to 6.2 6/24: Defoliate Canopy a bit and Topped off buckets, adjusted pH to 6.2 6/25 Trim up canopy again. Topped off Buckets, adjusted pH to 6.2 6/26 Trim up canopy again. Topped off Buckets, adjusted pH to 6.2 6/27: Changed Buckets, adjusted pH to 6.2, Trimmed up canopy again.

Still no sign of flowering. Transplanted Novarine plant 2 into a 50-liters container. The spot is under a big shorea plant. Shorea is a South East Asian medicinal tree. This is minimum light spot in my yard. Hope she would flower. I choose plant 2 because I think plant 1 will stretch even further. Plant 1 was also moved to a shaded spot under an tree jasmin. This Millingtonia, Indian cork tree. I have sweet flowers all year round. People told me that dried tree jasmine flower mixed well with weed and is good for people with ashma and sinus. Kind of useless since why would asthmatic people even smoke? Plant 3 is my back up until I come up with a way to put her into flowers. Clone are doing nicely. And I am growing 3 clones from plant 1 and only one clone from plant 2. I’ll be donating the rest to friends with weight and blood sugar issues. By year end, I probable keep only one or two clones. One clone from bigger branch is growing just fine without any benefit form lighted grow box. Feeding plants with mid-level dose of cow manure tea and earth worm casting tea to keep leaves healthy. They should have been given a light dose of fertilizer. However, the flowering purslane are also eating and feeding soil microbes. Got my paws on triancontanol and brassinolide. Perhaps these will jolt Novarine THCV into flowering. Triacontanol won't dissolve in neither water nor alcohol. And it is emulsified with polysobate. Mixing of Triacontanol Triacontanol does not dissolve in polysorbate. It is rather emulsified. Means that it need to be melt and there need to be water added. My steps, 1) heated 70 grams of polysorbate in a big heat resistance glass cup. I used a beaker. Mix in 5 grams of triacontanol. And it does not melt. 2) Put in 100 cc of water and put in microwave. After the mix is boiled, triacontanol melt. There is foam. So a bigger cup and a spillage plate would prevent problem with my better half. 3) After heated, the mix is better. Then I added hot water from to make total 250 CC of solution. Then, the mix is clear. 4) Label the dose with pencil. This works better than labeling with ink. I use 5 cc at a time for my entire garden. 250 CC would last me 50 doses. No need to buy so much. This is cheap. Let’s see next week how effective they are.