Processing
Likes
Comments
Share
Another watering planned for later today. Lights also changed over to 18/6 to try and control heat levels at night. New tower icolating fan placed in the tent. Lots of new growth, but leaves are slightly curled from heat stress I think. I will keep an eye out. Purchased an air cooler/humidifier placed on the outside of the tent blowing cooler air inside, both vents open with 1x icolating tower fan for the underneath and one fan blowing on top. Temp sitting at 25.5 (roughly) and humidity at 60%...its a little high but needs must. I think she may now be flowering. 🤔 Complete newbie, but white strands are starting to appear 😁 I need to move the light further away, she isn't that far from the top. Because of my restrictions with the size of the tent, I need to cut the top of the tent off and place a tall washing maiden around it and hang the light from that. Let's hope that works. Iv seen it done so I'm confident
Likes
19
Share
Trimmed a bit more & added a few more LST clips on day 74, watered with just Pro-TeKt to get the PPMs down still high at 2567 average, I may do so again next time, I suspect this coming week to be the final veg & will be flipping at the end of it.
Likes
17
Share
24.08.26 nachdem die kleinen Autos geerntet wurden konnte ich die großen Photos etwas auseinander rücken und mehr Platz schaffen. Das Blütenwachstum nimmt nun deutlich Fahrt auf und jeden Tag gibt es eine Hand voll gelber Sonnensegel die ich abpflücke. In ein bis zwei Wochen werden die Pflanzen deutlich anders aussehen und weniger Sichtschutz zu den Nachbarn bieten. Der Wasserbedarf ist mit den Temperaturen spürbar zurück gegangen. Es hat in der vergangenen Woche nach langer Zeit geregnet. Happy growing allerseits!
Likes
23
Share
Love this strain!! Nutty and meaty spicy terps one one of my favourite to medicate with and grow Both plants where grown in 1 gallon pots so nothing to big of a yield but was expected with the small pots . One plant was canna nutrients one was remo nutrients
Likes
5
Share
@hi_bengal
Follow
They pulled out of the power outage wish I coulda seen what they done without all the undue stress from bad temps and no light for a day....
Likes
4
Share
Week 3 Flower (Bloom Week 3) – Daily Tasks Evening (Lights On) Check environment (temp 24–27°C, RH 55–60%). Inspect leaves and buds for pests, mold, or deficiencies. Water/feed (depending on medium): balanced bloom nutrients with slightly higher P and K. Ensure good airflow (oscillating fans). Adjust plant training (light defoliation if leaves block bud sites). Check for early signs of stretch finishing. Evening (Before Lights Off) Ensure irrigation is not too late in the cycle to avoid wet medium during dark period. 👉 In Week 3 bloom, the plants are finishing their stretch and starting to put more energy into forming bud sites. Main job is: Setting Scrog net 2layers ,Control environment (VPD, airflow) ,Support the plant with bloom nutrients.
Likes
21
Share
This week so far has been a breeze she is very healthy and seems happy with her environment and feedings Successful week onto week 6 we go 🙌
Likes
17
Share
@Hashy
Follow
Week 10 Light cycle=12/12 Light Power=150w Extractor controller settings High temp=24c Low temp= c Temp step=0c High Rh= 50% Low Rh= % Rh step=0% Speed max=10 Speed min=1 Smart controller settings (during lights on). Lights on=10.01-21.59 Radiator on= below 22.0c Radiator off= above 23.0c Smart controller settings (during lights off). Lights off=22.00-10.00 Radiator on= below 18c Radiator off= above 19c Fri 23/2/24 💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧 Method= automatic Feed=bloom nutes. Neutralise=0.1ml/L Silicon=1.0ml/L Calmag=0.5ml/L Terra Bloom=3.0ml/L Sumo Boost=2.0ml/L P/K 9/18=1.0ml/L Easy Ph down=0.1ml/L Ec=1.9 PH=6.8/6.8 Time start=12.00pm Finish time=13.45pm (11×5 minute runs with 5 minute gaps) Total flow rate=190ml/min Flow rate per plant=47ml/min. Total volume made=13L(L) Total volume left=2.4L Total volume used=10.6L Volume per plant=2 6L (Est) Runoff. Total runoff=2.5L Ec=2.2 PH=6.2/6.3 💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧 #1 (Day 64)(Day 26 flower) 📋 tray is just high enough that they aren't sat in runoff. Sat 24/2/24 #1 (Day 65)(Day 27 flower) 📋 nothing Sun 25/2/24 #1 (Day 66)(Day 28 flower) 📋 Lowered light power from 150w to 140w Mon 26/2/24 #1 (Day 67)(Day 29 flower) 📋 Tue 27/2/24 💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧 Method= automatic Feed=water Neutralise=0.1ml/L Easy Ph down=0.ml/L Ec=0.2 PH=6.8/6.8 Time start=12.00pm Finish time=13.45pm (11×5 minute runs with 5 minute gaps) Total flow rate=190ml/min Flow rate per plant=47ml/min. Total volume made=13L Total volume left=4L Total volume used=9L Volume per plant=2.25L (Est) Runoff. Total runoff=0.5L Ec=1.8 PH=6.5/ Didn't run as should because forgot to plug it in. 💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧 #1 (Day 68)(Day 30 flower) 📋 Wed 28/2/24 #1 (Day 69)(Day 31 flower) 📋 Thur 29/2/24 #1 (Day 70)(Day 32 flower)**** 📋 I'm glad I removed a load of colas the other week because if I hadn't of done that I think she would be very overcrowded with no room between the colas. She is that tall that I can't get my camera in the tent to take pictures. At the moment I can just about pull her out the tent but I don't want to do that to much with me being very accident prone. Back soon. Take it easy.
Likes
325
Share
Hallo to You all my familly and usual visitors. Thank you for stopping by and all the likes and comments....You make my day! I gave the Blue Cheese a trim on 5th december and gave her four days of darkness, the chop was performed on december 9th I took a lot of photographs and videos commemorating these events for you to enjoy :) I think she came out quite decent especially considering that she had some monster/deformed leaves till the 4th week of veg. also looking back I should have moved her to the bigger place in that time...she would be far more symmetrical ;) It was a joy to work with Mars Hydro and their equipment in this grow. A big thanks to the Mars Hydro team for this opportunity, you truly provide first class grow kits and lamps. That's all i have for you till the drying & curing process is over I will update then. I want to thank you all for accompanying me in this journey, all the likes and comments...You growmies make me feel here at GD at home thank you 🙌👊😇
Processing
Likes
1
Share
Likes
117
Share
@BigDaddyK
Follow
Ok this is my Full guide with pictures on how to setup a Deep Water Culture grow, items you will need for this grow - Firstly a TENT or ROOM i use a tent REMEMBER stuff you buy NUTRIENTS off eBay and Amazon could be decanted (watered down) , or cheap chinese fakes (Ph Meters, PPM meters) you should really buy these things from you local hydroponics store,as they are guaranteed , i ve dropped a few into the bucket and they are fked,its been a sunday night with a bank holiday monday and i m fked, 1) Ph Down - makes the ph of water LOWER - this is VERY STRONG SHIT , wear gloves and googles if you are messing with it, i drop a bit into my main reservoir Ph 6.9 ( maybe 10ml per 200L) 2) Ph up - makes the Ph go higher - also STRONG SHIT -only needed in Emergencies 3) Ph meter 4) PPM Meter or EC meter 5) 20L Bucket + moulded lid netpot 6) Air Pump ,air hose 3m ,air stone x2, 7) Pebbles to fill to top of netpot, 8) ROOT IT cubes , i use these and ONLY these, by that brand,i know why,and so im telling you, 9) Seeds - I prefer Fast_Buds ,autos ready in 10 weeks of 18/6 - top quality 10) Nutrients, I use Canna as they are the easiest, they have a way of filling the one side , if you take the top off you can squeeze into the measuring side - I would also recommend Advanced Nutrients,but they are more expensive - so you will need 1L Canna Aqua Vega A+B ( it comes as two parts that you cannot mix together , when you put this into the water you MUST stir it well before putting each one in seperately otherwise you will get salts formed and crystals floating around,10 ml per 10L week 1-2 ,15ml per 10L week 3, 20ml per 10L in week 4) 1L Canna Aqua Flores A+B (as above) 25ml per 10L week 5, 30ml per 10L week 6 ,30 ml per 10L week 7 , 25ml per 10L week 8,15ml per 10L week 9, 0 per 10L week 10 250 ml Canna Rhizotonic (roots love this use this from start 20 ml per 10L and cut down after 4 weeks to 5ml per 10L up until week 9 250 ml Canna Cannazym ( breaks down dead roots, enzyme of some sort) 15ml per 10L from week 3 through to week 9 250 ml CannaBoost - (quite expensive but worth it, DWC will show you why) 15ml per 10L week 3 to 4 , 25ml per 10L week 5-9 250 ml Canna PK 13/14 (bud booster) this is optional because you only add it once,personally i add 15 ml per 10L in week 7 so its stays in for 10 days I leave my water for at least 24 hrs before using it, in a big old olive container i bought , i think its 225 L i might be wrong, but it was cheap , solid and had a top :) I check my water levels ,my PH and PPM daily 11) Jubilee clips x3 - to secure the fan ,filter and outlet.( 5 clips if using air cooled hood ) 12) Fans - i have 2 little fans and 1 big one = think about it, outside there is always good air flow - 13) Extractor fan -mine is 6 inch 14) Carbon Filter - mine is 6 inch im not overly impressed with any brand. 15) Ducting- 5m of 6 inch easy enough,well for me... 16) Ballast - LUMATEK -i found this one amazing and switchable. 17) Lightbulb -600w HPS ALL THE WAY but i would use 1000w HPS if i could keep the heat down, they both fit in same fitting 18) Air hood - i have a MAGNUM superXXXL it has screw in holders for glass , they are quite tight 19) Timer for lights , must be good quality , I do 17 hrs on 7 off as it's more natural 20) Syringes for measuring accurately 21) Bucket to mix solutions THE GOLDEN RULE - you can always put in but never take out - never put in too much or undiluted into the reservoir unless you really know what you are doing, less is better than too much . Ppm v EC - you may well buy an EC meter instead of ppm meter there is an easy way to convert between the two ~ 1.0 ec = 500 ppm EC multiply by 1000 then divide by 2 to get ppm This diary will start shortly but as so many people ask me how to setup HERE YOU GO :)
Likes
13
Share
Week 6 day 1 video Week 6 day 4 video I’m still pushing very hard with carbs every watering, humic acid, soluble n, soluble pk, microbial mass, b+, fishshit. Already tried testers for lowers. Very potent hits harder than a pen. Feels like 30-40% baked for 1-3h per j, different phenos. Not harsh just testers dried for 0:01:15, checked seeds and developing for 2-3 weeks
Likes
1
Share
@Thedibber
Follow
Made up all 8 are still going well 5x dip n stax and 3 pyschoberry cheese
Likes
2
Share
@GorkedOut
Follow
Week 10. I am still trying to get the ladies back on track, as my Ph meter was off a bit. I re calibrated and they should be good to go from here on out. The toads are starting to pack on weight and when I open up the tent it smells very tropical. Super frosty christmas tree structure. RH is around 50-52%. Temps around 73-78 F. Lights cranked up to 70-75% (500ish true watts) They're hungry and I'll feed them good.
Likes
4
Share
@AustinRon
Follow
OG 4Q24 Flower Week 9 Orangegasm (Fem) [ IRIE Genetics ] 12/12 @ Bolt (Day 21) Germination: 20 November 2024 #3A Earliest Harvest Date: 9 February 2025 #3B Latest Harvest Date: 19 February 2025 _________________________________________ Start of Week: [Wed Feb 5, 2024 CR2 4Q24 57:F:8:1] End of Week: [Tue Feb 11, 2024 CR2 4Q24 63:F:8:7] OrangeGasm Fertigation: - MAX: EC: [ 2.4, mS] #Ramping Down - LightIntensity MAX: [ 850, µMol/m2/s] ______________________________________ OBJECTIVES - Ramp EC from 2.4 - 1.0 - Start rolling off Primer A&B/Silica Skin to Resin Bloom . . . __ Wed Feb 5, 2025 OG 4Q24 57:F:8:1 EC: 2.3 Notes: #5 looks like a 60 day plant, if so - consider Saturday Harvest … Runoff - [x] Amount: [ 0.125 , gal] - [x] EC: [ 4.4 , mS/cm] - [x] EC∆: [ 2.5 , mS/cm] # Fried Yet? ;-} Harvest Dehu - [x] Amount: [ 1.5 , g] __ Thu Feb 6, 2025 OG 4Q24 58:F:8:2 EC: 2.3 Refresh Reservoir - [x] Amount: [ 2 , g] - [x] EC: [ 2.3, mS/cm] - [x] Primer A&B: [ 31, ml] - [x] Silica Skin: [ 15 , ml] __ Fri Feb 7, 2025 OG 4Q24 59:F:8:3 EC: 2.3 __ Sat Feb 8, 2025 OG 4Q24 60:F:8:4 - [x] Disassemble, Clean Reservoir and Pumps, Reassemble Refresh Reservoir - [ ] Silica Skin: [ 15 , ml] - Dropping Silica Skin due to (sparse to medium) granular precipitate - [x] Amount: [ 6 , g] - [x] EC: [ 2.1, mS/cm] - [x] Primer A&B: [ 100, ml] EC: 2.1 @1900 - Clear Manifold Filter. (Mainline should be cleared on 1845 feed __ Sun Feb 9, 2025 OG 4Q24 61:F:8:5 - [x] Dilute to EC 2.0 - Flooded Tent, 2 Gallons PLUS of Runoff. Happy Plants. - Shout Out Shop-vac. ;-} EC: 2.0 __ Mon Feb 10, 2025 OG 4Q24 62:F:8:6 EC: 1.8 HAND APPLICATION Prepped One Gallon of 12-8-7-5 @ 1.8 mS/cm w/ PhotoSynthesis Plus, SLF-100 Reclaimed Dehu Water, ~2 Gallons Refreshed Reservoir, 2 Gallons Rooted Leaf Hydro no Silica Skin, EC: 1.8 mS/cm Reduced watering to 5 min, then 1 - 1 -1 -1 -1 -1 -1 -1 (It’s not like they’ve been under-fertigated) __ Tue Feb 11, 2025 OG 4Q24 63:F:8:7 EC: 1.7 - [x] EC: [ 1.7, mS/cm2] - [x] Refresh Reservoir - [x] amount: [ 2.5, gal] Runoff - [x] Amount: [ 0.5, gal] - [x] EC: [ 3.6, mS/cm2] - [x] EC∆: [ 0.9, mS/cm2] # Better than 2.5! PLANT POSITIONS 3 5 1 7 4 2 6 8
Likes
13
Share
@Damonkey
Follow
Everything went well right through flush the last to show amber trichs were the Banana Crack, on harvest everything was well ready to come down. Everything is hanging to dry I’ll complete the harvest section in about a week. I’ve tested all three. Zour Apples is an Indica beast, super strong and dank. Banana Crack is a Sativa with a kick, it’s good and tastes great, strong bananas and ripe fruits. The Cherry is fantastic, smooth sweet and strong. All drying steadily 5 days down.
Likes
24
Share
Easiest harvest we ever did (in our short career lol), the plant lost many leaves by herself. she has a strong flavour and we literally cant wait to smoke her.
Likes
13
Share
@Lfuego22
Follow
Still in veg nutrients. Day 1-2 some swazzing Day 4 flower Ppm 1151 EC 2.2 Ph 5.7 Water temp 73.1 Room temp 71.2 Room humidity 60% Light temp 74.7 Light humidity 52% Day 7topped off water and nutrients