Temp and humidity stable. Ready to push 2nd half of veg. I’m mixing training techniques but confident I can get an even canopy. Trellis ready as a back up

🍀Estuvo bien en toda su etapa, no tuve ningún problema. Los resultados fueron muy buenos, se encuentra muy resinosa y con aroma a dulce. 🍀En total saque 143g de una sola planta. 🍀En total estuvo 105 días de vida desde su germinación. 🍀Recomiendo esta genética, por el momento son cocos Premium, ya quiero probarlo para saber que sabor tiene. 🍀Ahora se encuentra en etapa de secado, cuando ya estén para la etapa de curado subiré más imágenes. 🍀🇦🇷Podes seguirme en Instagram como @bruweed_arg🍀🇦🇷

13/04/2026 Midday Upped Redox therapy to 3 drops every 2 days with 3ml of hydrogen peroxide 17/04/2026 18/04/2026 Bubblegum Miniature is showing aging of dark purples!

Hola, solo les estoy dando agua. Hay una que viene un poco atrasada. Seguramente la proxima semana haga el corte. Saludos!

I got a double scrog setup and I'm gonna let it grow into it. This is my first grow and I'm excited. General Hydroponics nutes (Flora series). Kingbrite QB 288 v3 from alibaba. I'm just gonna let her do her thing until about week 3.

1/20/2023- So much to do pre grow and over the next 16 days, absolute first order of business is that I have to take down my current Grow---TIMBER-- Then I have a list of things I have to get done in order to be ready to start this grow 1 Feb. With that said T - 2 days until start 48 hour Flush T - 2 days until Start 48 hours of Light T - 4 days until TIMBER!!! Items that need to be done before 1 Feb 2023 1. I need to clean the tent out 2. I need to clean the equipment- Proper Sanitization between grows in Hydro is a must!!! 3. I need to get the hole in the ceiling above my tent repaired- For my last grow I had a deep sink installed in my grow room, to make Hydroponics a little bit easier and have a water source in the same room. The seals on the pipes they were installing broke and leaked through the ceiling causing some damage all the way across my grow room, I was already weeks into my grow and couldn't risk them working above my tent and it would have been very awkward positon for them to be working in as well, so have to get this done quickly between chop and germination. 4. I have to install my new light- I was using a Vivosun 4000 and for this grow I am switching up to a Spider-farmer SF 7000. 1/20/23- For this upcoming grow I am working with M/F photo seeds so I ordered 4 Sex determination kits. I recieved my my 4 Sex determination testing kits from Rimrock Analytics today. I will be using these to test my plants at week 2 of Veg so that when/if I take clones I know I am taking them off females. As well as I don't want to accidently pollinate my tent during this grow I am looking for big beautiful buds not seeded buds. :-) 1/24/2023- Harvest of current grow- Started at 2:00pm and finshed wet trim and firt batch into the freeze dryer. 1/25/2023- Next batch into the freeze dryer and cleaning all my equipment for this Grow. T-1 Day until the workers are supposed to be here to fix the hole in the Grow Room. T-3 days until I instll my new Gorilla Grow Tent and my New Light Spider Farmer SE-7000 for this grow. T-7 Days until Start of Germination 1/26/2023- Harvest is done ran through the Freeze dryer and dry tim completed. 1/27/2023- Grow Room repairs completed. Hole is gone Letting the paint dry before I install the new tent. T-2 days until Install the New Gorilla Grow tent and the new Light T-3 days until I put the hydro equipment in the new tent T-5 days until Germination 1/29/2023- Day 0- Final Pre Germination activities Germination Start T-3 days The paint on the ceiling was dry and it was time to finish prepping for Germination. I got the following items knocked off my list. New 4X4 Gorilla Grow Tent is up and ready New Spider Farmer SE-7000 Light is installed- Thanks Moony Grows for the suggestion and for the Code that got me some money off and free shipping (Moonygrows)!! I turned the lights all the way up to max and set the timer to 18/6 0600-0000. I will keep an eye on the temperature and humidity without my plants and see how hot it gets with the new light. I put my Hydro system back together and put in 40 gallons of water into it, time to monitor for leaks the next few days. I Setup my cloning machine for Germination Days 3-11 1/30/2023 let me break down the situation, ROOM in the TENT.. Enough said.. No really I tried putting my exhaust system up in the new tent with my new light, The light is so big corner to corner that it really didn't give me enough room for the lights be be raised, with the exahust hanging the buckets my plants are Starting in are 2 and 1/2 feet off the ground, great for plenty of room for roots but not so great for upwards space for the plant to grow. In a 6' 11 tent with the exauhst in side and hanging that only gave me a little over 4 feet of grow room to play with. My last grow if you saw my diary, anyone could tell I was struggling to keep the buds off the lights. No good, Since space was such an issue I was running my carbon filter inside on the ground but It really needed to be up sucking the heat out not shooting the cool out. With that setup I was sucking air through the filter and pushing it out the tent at a bottom exhaust hole cold out. Wasn't doing me any good for my heat. I was hitting temps of up to 85 degrees. I bought a portable AC unit and have been running it in the grow room to try and keep temps below 85 and I have had to lower the power on my lights during grow also not ideal.. With that said a friend of mine MoonyGrows (Check out his diary) took the time to look at my issue send me a picture of my grow tent setup with detailed instructions on how to suck the air out from the top but putting my filter and fan on top of my tent so no room issue and I am sucking the air out from the top where the heat is instead of pushing the air out from the bottom where the cool is... THANK YOU MoonyGrows For taking the time to help me get this straightened out.. Now I have room and I have the exhausts working right and now my temps with everything at 100% are topping out at 80 this dropped the temp by 5 + degrees at 100% max. T-2 days until Start of Germination Prepped my seed tray with humidity dome Prepped my Rapid Rooter plugs. I Used RO water, and I added a few drops of Hydrogen peroxide to Oxygenate the water. I then PH balanced between 5.7-6.0 the same that they will be getting in the Cloning Machine and when they get to thier final grow pod. I perfere the 5.8x range and I hit 5.84 for these rapid rooters. If you want to see a complete video on the process HowWeedGrow has an amzing video that shows step by step how to do it and explains it better than I ever could including how to plant the seeds. Which I will cover when I get to that step on Wed. https://www.howweedgrow.com/how-germinate-weed-seeds-cannabis-rapid-rooters/ 1/31/2023 T-1 day until Germination Start All set and ready have my Rapid Rooter plugs ready to go have my seeds out.. Have my seed tray warming up tonight. Tomorrow morning right into the Rapid Rooter then strait into the tray. I will spray the dome to start the humidity in there. 2/1/2023 Germination Day!! Let the games begin! 0600am Put the seeds into the Root Riots. And then put the seeded Root Riots into their first home the Seed tray. I have them under the light 24/7. Sprayed the dome 7:30pm Sprayed the Dome to keep humidity going on the dome. 2/2/2023 Day 1 of Germination Sprayed the Dome in the morning Sprayed the Dome in the evening 2/3/2023 Day 2 of Germination Roots are starting to come out the bottom of the root riot plugs and the heads are slowly popping out of Number 4 just below the surface. Afternoon- Number 4 has popped up Evening- Number 3 has popped up as well. Happy Dance!! 2/4/2023 Day 3 - Germination Surprise Surprise Surprise- all 4 have now poked their heads up.. Happy day!! 100% Germination succeeded. Now major milestone to track is how many are female and how many are male. I will take look at the roots this afternoon/evening and see if they have enough root to go into the cloning machine for the next 7 days before they go into their Hydro Pods. Day 3 - Germination - Evening.. Roots looked good and they were tall enough to make it into the cloning machine. Now that they are all in the cloning machine I have switched the lighting to veg state 18 on 6 off. 2/5/2023 Day 4 - Germination - Morning All the Ladies (fingers crossed) looking great stretching nicely and look nice and green, Photo synthesis underway.... UPDATE!! After a very interesting POD cast on FSTS by Dr. Bruce Bugsbee from Utah University, I have shifted my lighting to 24 hours on through seedling and then I am going to shift to 20 hours on the rest of Veg. 2/6/2023 Day 5 - Germination While Checking on my conditions inside the new tent last night, I found that the Humidity was down to 39 Percent. I added an AquaOasis Cool Mist Humidifier, the reason I selected this humidifier is that I needed one that could be turned on and off utilizing my Inkbird Humidity Controller IHC200 that I have my Pro Breeze Dehumidifier currently running with. Root structures are starting to get there about 1/4 of an inch. 2/7/2023 Day 6 - Germination Everything seems on track more roots poking out of each today. They are each getting a little taller as well. Checked in the evening and number 3 was drooping the Root riot plug on the bottome was dry and the roots were not in the water yet. I raised the water just enough that the longest root that was sticking out is now hitting the water. 2/8/2023 Day 7 - Germination Everything looked good while checking in on them this morning number 3 is now full up and no droop again. 2/9/2023 Day 8 - Germination T-2 days until Plant into Forever Pods and we start week 1 of Veg .. :-) Surprising thing to me is that number 1 and 2 were later in popping then 3 and 4 but the roots are growing longer in 1 and 2. 2/10/2023 Day 9 - Germination Number 1 and Number 2 are definitely ready for transplant today.. Based on how they were yesterday and where they are today I am hoping by tomorrow 3 and 4 are ready. Today they look to me where 1 and 2 did yesterday.. I really hope 3 and 4 catch up by tomorrow since.. T-1 day until transplant to new/ final home for grow. Need the roots long enough to have some clay down in the basket to keep the root riot out of the water and only roots in the water.. 2/11/2023 Day 10 - Germination Today they got placed in thier forever Home, 7 days from Sprout and 7 days until Week 1 Start. PPM- 180 this is water out of the Tap Temp Water: 70.7 Temp Tent: 77 Humidity: 40% I have a humidifier going 24/7 to try and bring this up.. I also have Humidity Domes on each plant. 2/12/2023 Day 11 - Germination Sprayed the domes, all are looking good.. Nothing much to do at this phase but Keep monitoring the PH level in the system and making sure they have a comfortable home. T-6 days until Week 1 start 2/13/2023 Day 12 - Germination Sprayed the domes, They were looking a little yellow today so I moved the light down to assist. Nothing much to do at this phase but Keep monitoring the PH level in the system and making sure they have a comfortable home. T-5 days until Week 1 start 2/14/2023 Day 13 - Germination Sprayed the domes, They were looking a little Florissant yellow today, with what looks like slight burn on the tips, I talked with a fellow grower and we agreed that It was probably that I was drowning them, Yes you can drown you plants even in Hydro, but only early on.. :-) It usually happens with the water being too high, which soaks not only the roots but the medium (root Riot plug in this case). I lowered the water from touching the bottom of the pot to about 1" away. This will probably take 3-4 days to resolve. I will continue my daily monitoring. T-4 days until Week 1 start 2/15/2023 Day 14 - Germination Sprayed the domes, continue my daily monitoring they look a little darker green instead of lime green now that I lowered the water levels in the system, so I think that I might have resolved the issue but it will take a few days for recovery to happen. T-3 days until Week 1 start 2/16/2023 Day 15 - Germination I looked in on them this morning, 3 and 4 look like they are doing well and recovering nicely. Number 1 not so much it has brown spots on the leaves, this very well can still be a side effect of the overwatering but I decide to go ahead and add Nutes earlier than I was planning just incase. I was going to wait until Saturday but I think intervention is necessary now especially after drowning them early on. I added 1/2 what I am planning on adding for week 1 start. I also think I am going to adjust my chart to add 1/2 2 days after plant from now on. I don't think it would hurt it to have some Nutes to pull from. .25ml/Gal Calmag = 12.5ml 1ml/gal GH FloraMicro= 50ml 1ml/gal GH FloraGro = 50ml 1ml/gal GH FloraBloom = 50ml T-2 days until Week 1 start = I will drain the system and start it over on Saturday with Week 1 Nutes. 2/17/2023 Day 16- Germination I didn't even want to post today after looking in on them this morning, 3 of the 4 are now showing signs of dronwing.. Brown spots on the leaves, the water levels were still too high.. I drained about another inch out of the tanks.. Will see how quick they recover.. I start week 1 tomorrow and will have to ensure my water levels are at least 1" away from the basket on this round.

Week 6/5 - 12/5 Next week 50L of water to flush.

Finally!

Despues de leer creo que el problema puede ser de los LEDs+Calcio, añado calmag y bajo potencia hasta 250w, ahora esperar. La planta que no tenia problema empieza a tenerlo.

She looks fantastic, the smell of the buds is very kushy I can feel some piney notes and also some earthy notes, week see how she keeps developing those purple buds! 💚 🌱 ✌️ 💎

😈👹😈👹 DARK DEVIL AUTO®️!!! 😈👹😈👹 Finally getting around to a strain I’ve been dying to grow! I’m hoping for a successful germination rate, keeping my fingers crossed!🤞 For these girls I’ll be growing in two different mediums with a variety of nutrients and amendments from various brands. Of course as always, all inputs are 100% organic. No synthetics allowed in my garden! Two Dark Devils will be grown in Nectar For the Gods #4 Soil Mix and the other who will be grown in Malibu’s Baby Bu’s Potting Soil. Both of these mediums are considered premium and only have the best quality inputs. Both soils also contain coco coir. In my experience I have found that autoflowers grow so much better in soil mixed with coco. Anytime that I’ve grown in heavier based peat soils I get much smaller root balls and root mass in general compared to coco/peat mixed mediums. The NFG #4 is a much lighter substrate than the Bu’s because it’s filled with a ton of perlite and pumice. One benefit is that it also has basalt so it’s considered “paramagnetic”. The one thing I added to the NFG mix was organic Bio-Char blend made from Build A Soils bio char and locally sourced organic bio char. The Baby Bu’s medium is 100% Coco Coir based, mixed with their biodynamic compost, worm castings, bio char, and tons of other beneficial ingredients. This medium is slightly heavier than the NFG even though the NFG is peat and coco based. It really comes down to there being less aeration material in the Bu’s blend compared to the NFG. But hopefully the coco will make up for the lack of aeration compared to the Nectar #4. A benefit claimed by both companies is that their products are properly mixed and stored so the customer does not receive “HOT” soil. The mediums come lightly pre-amended but believe that the Baby Bu’s will have more nutrients than the NFG #4 mix as they claim their soil is an “all mix”. I will be feeding the plants with living oxygenated water, microbial inoculants and light compost teas until the plants look like they need more food. This is my first time growing in both mediums so we’ll see as I grow along! I will also be adopting the northern lights technique that I’m using on my Banana Blaze grow diary! Update: 12/16 All four seeds broke ground around the same time at 9:00pm. 100% successful germination rate. Let’s see how they progress into the vegetative state. Update: 12/18 one out of four seeds may be showing signs of damping off. All four were growing straight as an arrow but today one is slightly slouched and leaves are allowing water to soak in. This usually isn’t a great sign! Update: 12/19 Took the suspected damping off seedling out of her humidity dome and she improved overnight. She is the only one with a greenish colored stem while the other three all have distinctive red/brownish stems similar to other purple strains I have grown. Thanks for stopping by! 😈

Well, there’s no ghost the VIVO sun pumps that come with the kits they just suck that’s OK. I replaced them with the upgraded version. I refilled the reservoirs

A tad late, but on Dec 20th we started flower! The pics and video are all from dec 20. To kick it off we did a small feed (1tbsp) of veg nutrients and over the next few weeks will transition to flower blend. So far she's taken well to the training and looks very strong overall. Cheers til next time -Dj Sunstone

LJ4Q23 Bolt III SOP LJ4Q23 - 8-Plant SOG from Cuts Objective: - 8 Plants - Single Colas - No Branches - Harvest Lemon Jeffery (Narrow Leaf Phenos): 70±5 days - Light Intensity - Ramp up from 200 - > 40 DLI, at 13 hour ScotoPeriod, will need MAX Light to Achieve - Ramp Light Intensity to MAX ASAP (3 Weeks?) Notes: - Lemon Jeffery handles HIGH LIGHT Well, even within 6” of Light @ ~1800 µMol/m2/ - The challenge will be achieving minimum 40 Mol/day, which in this setup requires 1000 µMol/m2/s @ 13 hour Scotoperiod ______________________________________ Start of Week: [ 2023-12-13, LJ4Q 15:B:2:1] End of Week: [ 2023-12-19, LJ4Q 21:B:2:7] Environment Targets (Bolt III): - Scotoperiod: [ 13, h] # Contiguous dark hours daily - DayPeriod: [ 1900, 0600 +24h] - TemperatureMax: [ 78, °F] #CHANGE from [82, °F] - RH: [ 68, %] - VPD: [ 1.0, mS] - LightIntensity: [ 850, 1000, µMol/m2/s] - LightDistance: [ 16.5, “] Bolt III Fertigation - RLA HYDRO Chart, Week 4, EC: [ 1.8, mS] - Primer A: [ 8.5, ml, gal] - Primer B: [ 8.5, ml, gal] - Silica Skin: [ 4.25, ml, gal] All Fertigation Add - Plant Success: - Microbelife Photosynthesis Plus: [ 0.5, ml/gal] - Build-a-Soil: - Quillaja20 Powder: [ 0.5, tsp/gal] - South Cascade Organics: - SLF-100: [ 5, ml, gal] __ Wed Dec 13, 2023 LJ4Q 15:B:2:1 LightIntensity: [ 932, µMol/m2/s] DLI: [ 35.1, 11, mol/m2/day] # On our way to 40 DLI Popped above 12” Plant Height (13 - 14”) 24# Photone Filter, Add 10%: 848 x 1.1 : 932 - [x] Measure Runoff - [x] Amt: 600 - Reduced Irrigation Event from 2:30 to 2:15 - Measure Thursday, Adjust. Foliar: - [ ] CalMag Fuel: [ 20, ml/gal] - [ ] Peak Bloom: [ 5, ml/gal] __ Thu Dec 14, 2023 LJ4Q 16:B:2:2 - [x] Reset Intensity - LightIntensity: [ 838, µMol/m2/s] # Calculated, 24# Filter, +10%, 762 Measured, 30.1 DLI - [x] Change Light Distance: [ 19.5, in] - [x] DLI: [ 33, mol/m2] - [x] Measure Runoff - [x] Amt: [ 400, ml] - 8 X 4400 X 10% (Field Capacity): 3520 Max, 350 - 450 is the target runoff per day - 15 sec: 200, ml. 200/15 ml/sec / 8 plants: 1.6 ml/sec. Close to our 1.7 ml/sec per plant Consider that - So we want field capacity per day, until we’re showing drought stress. - 4400 ml X 10%: 440 ml/plant/day - 110 ml/plant/event - 4 events/day - But that would only be 64 seconds, not current 135. - Let’s reduce again to 2 Minutes total, and evaluate. GUESS: If Linear, we should have 200 ml runoff __ Fri Dec 15, 2023 LJ4Q 17:B:2:3 Res: [ 4, gal] Environment Actuals - Scotoperiod: [ 13, h] # Contiguous dark hours daily - DayPeriod: [ 1900, 0600 +24h] - TemperatureMax: [ 78, °F] - RH: [ 67, %] - VPD: [ 0.86, mS] - LightIntensity: [ 838, 1000, µMol/m2/s] - LightDistance: [ 19.5, in] - [x] Refresh Reservoir - [x] 4 Gal - [x] Change Irrigation Duration Before 1845 - [x] IrrigationDuration: [ 2, min] - [x] Measure Runoff @1930 - [x] Amt: 180, ml. # after 2 fertigations 🤨 - Raised Fertigation per event to 2:15 fm 2:00 Guesstimate: 120 sec * 1.7 ml/sec: 204 ml I think we’re closer to 0.8 ml/sec: ~ 100 ml per delivery (2min) Refresh - 4 Gallons - Primer A: [ 36, ml] - Primer B: [ 36, ml] - Silica Skin: [ 18, ml] - King Crab: [ 2, ml] - Terps Plus: [ 2, ml] - Quillaja 20: [ 2, tsp] - SLF-100: [ 20, ml] - EC: 1.8 Res Temp: [ 60, F] Irrigation Timing Update Initiate Irrigation Irrigation Complete Event 0 18:45:00 18:47:00 Event 1 21:30:00 21:32:00 Event 2 00:15:00 00:17:00 Event 3 03:00:00 03:02:00 - Foliar: - [ ] Solar Rain: [ 20, ml/gal] - [ ] Peak Bloom: [ 5, ml/gal] __ Sat Dec 16, 2023 LJ4Q 18:B:2:4 - [x] Measure Runoff - [x] Amt: [ 250, ml] We really need the additional 15 seconds, reset today: Initiate Irrigation Irrigation Complete Event 0 18:45:00 18:47:15 Event 1 21:30:00 21:32:15 Event 2 00:15:00 00:17:15 Event 3 03:00:00 03:02:15 __ Sun Dec 17, 2023 LJ4Q 19:B:2:5 - [x] Measure Runoff - [x] Amt: [ 230, ml] #1930 - LightIntensity: [ 1047, µMol/m2/s] # 110% of Photone 952 - DLI: 61.7 __ Mon Dec 18, 2023 LJ4Q 20:B:2:6 - [x] Measure Runoff - [x] Amt: [ 80, ml] - On the theory that the main feed line siphons back to res, despite back flow adaptor - Add 45 Seconds to FIRST Feed of Day to Assure Priming and delivery of feed water. - Add 15 Seconds to remaining 3 __ Tue Dec 19, 2023 LJ4Q 21:B:2:7 - [ ] Measure Runoff - [ ] Amt: Added :45 to initial fertigation, :15 to remaining. Initiate Irrigation Irrigation Complete Event 0 18:45:00 18:48:00 Event 1 21:30:00 21:32:30 Event 2 00:15:00 00:17:30 Event 3 03:00:00 03:02:30

on va continuer le journal un peut différemment. parlons vacances et hash fait maison que j'ai fait avec la frostbanger et ma purple haze qui se sont transformé en un haschisch extrêmement huileux. quelques chose de magique l'autre que j'ai préparé avant de partir est resté un peu poudreux. Pas assez de curing pour le hash . primordial de lui laisser le temps de mûrir en espérant que cela vous plaise. et on m'a fait une photo. désolé de la qualité de la photo mais elle a l'air de bien se porter bon visionage

Deze week werd verstoord door een stroomstoring van een dag (oorzaak gelukkig niet in de kweek apparatuur!) Er zijn inmiddels veel meer lieveheersbeestjes, erg leuk om ze te zien hoe ze hun eigen gang gaan. E.c. zit inmiddels op 1,3/1,5 Dit lijkt misschien wat hoog, maar de stekken kunnen best wat hebben. De dames groeien zo hard dat ik nog een keertje blad heb moeten wegknippen om de boel niet t laten verstikken bij de Powerplants.De Runtz begint al topvorming te laten zien. Ook een irrigatiesysteem aangelegd. Dit is later handig als het bader dek te dicht is en je niet meeer overal bij kan komen. Regeren is vooruitzien ! UPDATE!!! Vraag aan de gemeenschap die ervaring heeft met cree cobs: Ik heb begrepen dan de cobs een kleine 20 cm door het blad dek kunnen penetreren als je goed hebt ontbladerd. Aangezien mijn scrog maar max 40 cm hoog word, heeft het dan zin om de boel in week drie te dieven? Het licht bestraalt immers de hele plant? Antwoorden graag in de comments!

I have spent the week bending and tightening all the bondage straps to maintain the even canopy I'm after and allow for maximum footprint. I expect during this week she will get a net slung over her as I am running out of pot circumference to keep using ties. I need to work it all outwards now . She got a spray of boom boom spray this week after the heaviest HST session. It's a Foliar biostimulant that helps the plant recover from stress.. mixed 100ml to 0.5ml of boom spray and applied at lights on Still feeding just plain untreated tap water. About 1l a day ATM. Lights are at 60% and environmental figures are spot on. This is a super healthy plant . I am very very impressed with biotabs as a product. So easy ..