FOR EVERYTHING MARS HYDRO VISIT: www.mars-hydro.com www.marshydroled.ca PROMO CODE: rocknroll VISIT THE ALIEXPRESS STORE: @marshydro_aliexpress Instagram: @marshydropenny REMO NUTRIENTS 👍 Thanks for taking the time to read and check out my diary🤜🤛 TS3000 FEATURES: WIDEBAND SUNLIGHT FULL SPECTRUM LED GROW, Infinite close to natural sun light, suit for all plants whole stages indoor growing, rapid plant response from seed to flower, achieve maximum quality and quantity, much better than traditional HPS grow systems. HIGH REFLECTIVE & NOISE FREE-Fanless LIGHT BOARDS design will make your growing life easy and quiet, quickly heat dispersing material aluminum reducing light lost to aisles and walls, increase the light intensity up to 20%, allowing your plants receive more energy and without burning your plants for maximum headroom. HIGH EFFICIENCY ENERGY SAVING PLANT LIGHT, high-power NEW LED grow, Compares to traditional 3000 watt HPS lamp and other brand led grow light while only 450 watts true output with 1016 LEDs, more scientifically and energy-efficient! Perfect for 5' x 5' veg stage, 4' x 4' bloom stage, higher intensity in a MARS HYDRO grow tent, reflective area, or by crossing over using multiple TS3000. BOOM YIELD LARGE GROW LIGHT, NEWEST SMD LED technology provide highest PAR/LUMEN output(1095.6umol/), makes you get 30% higher yield compare OLD led lights, can get max yield at 2.5g/watt, less pay but get more yield, bring a amazing grow trip to any home grower as it beams huge amounts of light energy to plants below. COMMERCIAL LED GROW LIGHT, Updated easy dimming & daisy chain function, main light controlled, especially come with two waterproof and dimmable Mean Well Drivers, auto sensing power supply works on both 120VAC and 240VAC and 277VAC, suit for Large Rooms and Commercial Setups. Low Energy-Consuming LED Grow Light: Consuming 300w and also mounted with 1016 chips, TS3000 has the ability to replace a 450w HPS light while reducing 40% power intake. High Efficiency LED Grow Light: With overall light output PPF 343umol/S as well as amazing PPE 2.3 umol/j, it's 50% even more photon efficient and can assure a 30% more return than the old HPS/MH lights. Patent Highly-Reflective Hood Shape: The reflector design on TS3000 is patented, which can effectively gather the light dispersed in all directions to enhance its light intensity as well as assist plants in absorbing more light. Full Spectrum Plants Favorite Spectra: By the unique mix of spectra that makes most light in the 400-700nm waveband, incredibly conducive to plant photosynthesis. Adequate IR(730-740nm) is additionally consisted of in the range to generate larger buds. Dimming And Daisy Chain Feature Available: Upon an independent dimming button on the external driver, backing 0-100% settings adaptation and up to 30 LEDs daisy-chained in a group, it supplies different light levels for various plant stages meanwhile saving energy. Safety Certifications And Service Warranty: CE, ETL, RoHS, UKCA security certifications accepted, 50,000 hours durability, 5-year service warranty, and local after-sales repair 5x5 GROW TENT: LOCK ALL LIGHT INSIDE MARS HYDRO Indoor Grow Tent interior is made of diamond mylar which is highly reflective. (Other brand's mylar and reflective rate is as low as 50%, won't provide efficient light. )MARS HYDRO 1680D canvas, being double stitched, it is tear proof and has perfect light locking. Mars Hydro's grow tent keeps 100% lighting beams inside and helps your plant absorb more lights. EXTRA-THICK --No light leaks or rips at all DURABILITY GROW TENT Stable metal corner adapters and poles are the trustful supporters of the tent, standing sturdy, neither rusting nor paint-falling, quick easy tool-free installation. Mars Hydro's heavy-duty metal zippers, with double layer black lining, are the best on the market which create a light-proof seal EASY OBSERVATION FOR YOUR PLANTS. Special observation windows are made by double layers of cloth. Observe the growing conditions of your plants without opening the tent and avoid disturbing plants. The observation window also serves to dissipate heat and ventilate air AUTOMATIC 6 INCH EXHAUST FAN KIT W/ CONTROLLER: Mars Hydro 6'' Inline Fan uses a mixed-flow design to maintain peak performance in a high static pressure environment. GROW TENT FAN: MARS HYDRO inline fans are designed to ventilate hydroponic grow rooms, transfer heating/cooling, cool AV closets, and exhaust odors. EFFECTIVE VENTILATION: Variable speed controller for easy fan speed adjustment. Optimal ventilation for your planting. LOW NOISE LEVEL: Durable plastic fan housing and blades for extremely low noise(32dB-A); create a truly quiet growth environment. EASY INSTALLATION: Removable duct ends with locking tabs for quick removal and easy maintenance and a cord length of 4.9 feet for hassle-free setup. This grows tent fan with a controller for easy fan speed adjustment. BASIC PARAMETERS: Ventilation exhaust fan size: 6” | Dimensions: 315mm*225mm*210mm. | Weight: 2.7. | Airflow: 402CFM | Noise: 32dB-A | Bearings: Dual Ball. 

Been a week and half from I started the LST training, really starting to bush out so much. Growing really very!! Had some amazing hot days. Maybe to hot for a bit. Water system working really well. 👍😍😍😍😍😍😍😀😀😀😀😀 New photo today, not sure if she's in pre flower!? Should be seeing her in three days!! Let's see how bushy she got from the super cropping and LST. I'm hoping she will climb through the middle.

Beginning of week 7 in flower, only two more weeks left if they ripen like they did last time. Plants are beginning to smell, develop triches and fattening up. They're not going to get any taller but compared to my first grow they're double in size. It's getting really intense. I'm in there every day checking humidity (on the no defol side) and I'm starting to struggle keeping up with the feed. During lights off I've found the plants eat the most food. I topped up the res, added 25% more PK. I try to keep the plants at 700 ppm and in the space of four hours it dropped to 600 ppm (towards the end of lights off). I stopped directly loading with Calcium Nitrate and instead used a regular calmag. I'm about to go overboard with Calcium Nitrate again and bump the ppm up to 1k. Will see how far the ppm drops the next day. 17/02/20 Update: The plants are beginning to smell a lot more, it has that kind of fermenting pungent smell from a red paw paw but applied to a mango. Very sweet, it literally smells like I'm growing some kind of tropical fruit. Still struggling with the feed, I added close to 40g of calcium nitrate and the plants still dropped the ppm lower than when I boosted it. I find it really frustrating that Dual Fuel only sell as a pair. Part 2 is amazing for late flower. Potassium sulphate and Magnesium sulphate, it's the perfect PK boost and I don't know anyone other nutrient like it. The other PK boosters always have too much P. 18/02/20 Update: Still battling my plants and the efforts to keep up with them is still frustrating me. Ran out of potassium Sulphate and bought Bio Diesel Rhino K 0-0-15 as a substitute, talk about expensive but I was desperate. 19/02/20 Update: Uploaded how I pump calcium into my plants this late into flower. They eat more than what I showed daily. That's 100+ ppm of Ca everyday! I don't know how much pectin this plant has now but the Brix would have to be through the roof compared to my first grow. 20/02/20 Update: finally got the feed right for a twelve hour period. I'm using two times the amount of K any bloom booster recommends and I'm probably using ten times the amount of calcium easily. I'm also going to feed as minimal N from now on, I'd cut it out completely if I could but I rely on Micros for the macro nutrients. Spent $65 on that bottle of potash and I used a third of a bottle for one nutrient change, think I'll stick to using powered water soluble potassium sulfate. My main concern is that I won't be providing enough iron with the little Micro I'm giving it. Going to throw a couple of rustry nails into the res. I'm about to do a top up...dropping the Micro super low, putting minimal part 2 in. Along with all the fulvics, humics, kelp and other acids my ppm only sits at 244. Which gives me plenty of room to load up on calcium. Top up the mag cause what was in the part 2 wasn't enough then load K. 21/02/20 Update: The plants finally stalled and took a breather yesterday. Didn't upload any photos cause it looked the same as the day before. By the end of the evening it looked like the explosive growth started back up again and the photos from today will show it. The ppm was creeping up not down this time...finally over feeding them. Dropped the extra loading of calcium and potassium to regular bloom phase levels and bumped the chelators up instead. Update 22/02/20: plants aren't eating what they were. Ppm is remaining stable at 800. I won't dilute the res just yet. Still holding off to see if it goes up again. If it goes down I'll refeed the same formula as last time that has reduced calcium and potassium.

Day 28 She looks good but not perfect, wait for the next weeks ,also she is in preflower

Heya👍🤙👍🌱 Almost Done. I like early Harvest. Check out my Facebook profile: https://www.facebook.com/share/v/H6PnoahTHrEzm63U/?mibextid=oFDknk Big BIG BIG thank you to Sebastien, Heather from Fastbuds420. You guys are the best. Can't wait for the next live. Even Bigger shout out to Hydroponic.co.za. My local Hydro Shop and Sponsor. Thank you Sir. 👍🤙👍🌱

2000 ml alle 2 Tage PH-Wert: 6 EC-Wert: 1,6 Temperatur: 22ºC Luftfeuchtigkeit 62% Schädlingsbekämpfung: Nematoden PPFD: 510 µmol/m²/s DLI: 33 Düngemittel: Mineralischer Dünger 3,5-6-6 Besonderheiten: Wurden direkt in die erde gepflanzt in einer Kokos-Quelltabletten. -Tag 71 Heute haben wir sie mit 2000 ml Wasser gegossen, angereichert mit 1,5 ml Calmag, 4 ml Canna PK 13/14, 2 ml 3,5-6-6, 1 ml Plagron Green Sensation, 1ml Plagron Power Buds, sowie 0,32 ml HY-PRO Generator. Der EC-Wert betrug 1,650 mS/cm und der pH-Wert lag bei 5,8 😚 -Tag 73 Heute haben wir sie mit 2000 ml Wasser gegossen, angereichert mit 1,5 ml Calmag, 6 ml Canna PK 13/14, 2 ml HY-PRO Epic Blast sowie 0,32 ml HY-PRO Generator. Der EC-Wert betrug 1.540 mS/cm und der pH-Wert lag bei 6 Ihre Buds werden immer dichter und sie riecht sehr gut 😍 -Tag 75 Heute haben wir bei ihr den pH-Wert kontrolliert, und er liegt bei 6,6. Der EC-Wert lag bei 580. Wir haben ihr Wasser mit einem pH-Wert von 5,7 sowie Mikroorganismen mit Weizensirup gegeben. -Tag 77 Heute haben wir ihr wieder de Runoff Kontrolliert und er ist nach wie vor bei 6,6, wir werden ihr heute wieder Dünger geben. Ihr Buds werden immer Kompakter und sie hat einen Sehr intensiven Geruch bekommen 😍

Week 4: Heartbreak and Hope 🍍💔 The sight that greeted me today was devastating. Snails. Everywhere. They'd turned my once vibrant pineapple into a skeleton of its former self. I could barely bring myself to take a single photo, the sight was just too painful. Fueled by anger and determination, I launched Operation Snail Removal. Every half hour, armed with a flashlight and a bucket, I combed the raised bed and surrounding area. By the time darkness fell, I'd collected a horrifying 19 snails from her bed alone. Ugh. The next night, thankfully, was snail-free. I can only hope that the damage is done and my pineapple warrior can rally from this. I believe in her strength, her resilience. She's got to pull through.

Everything goes well. I have added a fan for an air flow, it reduced a bit the temperature inside the tent. Also I've made the first watering at day 12, about 2 liters per each 15l pot and added some soil, because the original soil has subsided. I used BAC foliar spray to spray leaves of the palnts

Cultivo LED The Smith 150w 4000k (Samsung) - Não tem opção de colocar esta marca no diário. Também estou a usar nutrientes, da kayasolucions mas também nao tem disponível para adicionar ao diario. Quem quiser saber mais, pode pesquisar The Jungle e uma growshop :)

Plants are growing at full speed and still looking good, roots grew so fast it's already time for a new transplantation. This time I did repot into 15L fabric containers (by Gronest). Medium is still made of pure soil (LightMix by BioBizz) then enriched with GreenBuzLiquids nutrients.

the two rainbows are on flowering Time and we also changed the ciclus for the san Fernando valley also from B.S.F. Seeds, we are expecting the TnB naturals #co2enhancerbottle

Candy kush express #3 should be done by the end of this month and she's chunking up very nice and the smell coming from her is like nothing I've grown before it's wild!! Candy kush #1 is loving the foop bloom and is almost as tall as my gp x bkp which is like 6 weeks older 😅 😳 amazing growth with this strain. Candy kush #2 is growing super unruly lol 😆 branches growing every which way going to be a unique looking plant when all is said and done,I would seriously recommend this strain for anybody growing outdoors ,I'll be ordering a 10 pack for next season(depending on the smoke,which I already know is going to be fire 🔥) I was forced to move all 3 plants out in front of my house because the sun is slowly moving back behind the trees later and later as these fall weeks move foward but my front yard stays lit up from around 930am-730pm luckily or I'd be screwed

Hello :) this is my second growth in nature this year, the first one was drowned...... but I hope it won't happen again and I will try to do it with car flowers :) I will leave the little ones on the balcony for another week :) and then they will move to their permanent place :) so far the girls look quite good, knowing that it's only been a week:).

I have finished this cicle, and this image shows you everything you need to know. OBS: UV light on the holl flowering stage, except in flush.

great, everything is going really smoothly, @Zamnesia Runtz auto, copes perfectly with leaf spot and LST, started to bloom, so I think it will soon stop growing upwards, and I won't have to hurt it anymore :) @Plagron This is the first time I've used nutritional fertilizers, but I already understand that it definitely won't be the last :) good luck to everyone :).

End of day 61 flower. Both girls have been sitting in the dark since Yesterday @8pm. Will be taking them down on Thursday afternoon. Split the stem on both and flushed with florakleen for 3 days and now only on RO water. Adding a few ice cubes to the solution 2 or 3 times per day to keep the temp down. The last 12 hours remaining I will take all the water out of both buckets to let them know that the end is near and hopefully get some more frost from that. It’s been over 120 days since these two got seeded together and it’s been one hell of a journey. I got a bunch of clones off them and will have more grows on those coming up soon. I’ve learn a lot about what these girls like and hope to get a better yield with the clones. Next update will be the harvest. Take care and thanks for following along. 🤗

They're getting juicy mm mm. Ran into a few issues with the root zone, but corrected things and we have continued forward.